Avaya 5600 Series Руководство по быстрой установке

Просмотреть онлайн или скачать pdf Руководство по быстрой установке для IP-телефон Avaya 5600 Series. Avaya 5600 Series 2 страницы. Gigabit, ip phones
Также для Avaya 5600 Series: Инструкции по установке и безопасности (11 страниц), Руководство по конфигурации (17 страниц), Памятка по установке (14 страниц), Информация о продукте (2 страниц)

Печатать страницу

Avaya

Ethernet Routing

Switch 5600 Series

Quick Install Guide

Before you start

You can download all documents referenced in this Quick

Installation Guide at www.avaya.com. You do not require a

support contract to download documents. When

downloading documentation, select the specific software

version.Depending on your hardware model, your switch

may appear different than the figures shown in this guide.

Confirm that you have the following tools and package

contents:

Tools Required:

• Phillips #2 screwdriver

Package Contents:

a. Avaya Ethernet Routing Switch 5600 Series.

b. Rack-mounting hardware that includes:

• Rack-mount brackets

• Screws to attach brackets to the switch

• Screws to attach the switch to the equipment rack—

choose the appropriate rack-mount screws for

attaching the switch to your rack.

c. Stacking cable

d. Four adhesive foot pads.

e. Country-specific AC power cord or DC adapter.

f. Power supply unit and related documentation.

Prepare the rack (if you plan to rack-mount the switch):

• A 5650 model requires 1U, a 5632 model requires 1.5U,

and a 5698 model requires 2U of vertical space for each

switch in an EIA or IEC-standard equipment rack.

• Bolt the rack to the floor and brace it, if necessary.

• Ground the rack to the grounding electrode used by the

power service in the area. The ground path must be

permanent and must not exceed 1 Ohm of resistance

from the rack to the grounding electrode. Avaya

recommends using a filter or surge suppressor.

Install the power supply unit or units

a. Push the power supply unit gently, but firmly, to insert it

fully into the internal connection port.

b. Secure the power supply in the switch by tightening the

two retaining screws.

Mounting Options

To install the switch on a table or shelf, attach the rubber feet

to the device as indicated.

Set the device on a flat surface near an AC power source,

making sure there are at least 2 inches (5.1 cm) of space on

all sides for proper air flow and at least 5 inches (12.7 cm) at

the back for power cord clearance.

To install the switch in a rack, attach the brackets to each

side of the device using the screws provided.

Slide the switch into the rack. Insert and tighten the

rack-mount screws.

Note: One 5600 Series switch weighs as much as 33 lbs

(15 kg). Avaya recommends that two people lift and install a

5600 Series switch.

For detailed instructions that describe how to install the

Ethernet Routing Switch 5600 Series, see Installing the

Avaya Ethernet Routing Switch 5000 Series (NN47200-300).

Powering Up

Connect the AC power cord to the back of the switch, and

then connect the cord to an AC power outlet.

For DC power supply units, ensure your DC power source is

switched off. Plug the DC adapter into the power supply unit.

Connect the DC leads to the adapter terminal block. Tighten

the screws on the top of the adapter to secure the DC leads.

Attach the opposite ends of the leads to a –48 V DC

power source.

Warning: You must use a line cord set approved for the

5600 Series switch and the receptacle type in your country.

Ensure you have properly grounded the switch before

powering up the unit.

Watch the front-panel LEDs as the device powers on to be

sure the PWR LED is lit. If not, check that the power cable is

correctly connected.

Front Panel 5632-FD

Front Panel 5650-TD

Front Panel 5698-TFD

You must start the switch, and the operating system must

successfully and completely load, before devices connected

to the switch can send and receive data.

Installation

Install SFP and XFP transceivers

Verify that the SFP or XFP transceivers and network cabling

support your network configuration. Note: The ERS5600

supports Hot-Swapping of SFP and XFP transceivers and

direct attach cables.

1. If you are installing SFP direct attach cables, remove

packaging, insert the transceiver connector into a switch

port and insert the opposite end into the SFP port of the

corresponding network device.

If you are installing SFP or XFP optical transceivers,

remove packaging and insert the pluggable transceiver

connector into a switch port. Proceed with the

following steps.

2. Remove the network interface cover from the transceiver

connector (if applicable) and insert an appropriate

network interface cable into the transceiver.

3. Connect the opposite end of the network interface cable

to your network.

4. In both cases, ensure that the device clicks and locks

into place.