KitchenAid YKEMS307GS3 Руководство по установке - Страница 4
Просмотреть онлайн или скачать pdf Руководство по установке для Печь KitchenAid YKEMS307GS3. KitchenAid YKEMS307GS3 10 страниц. 27" (68.6 cm) and 30" (76,2 cm) electric built-in microwave/oven combination
Electricalconnection
Electrical Shock Hazard
Disconnect power to the junction box
before making connection.
Electrically ground oven.
Connect ground with lO-gauge-minimum
solid copper wire.
Failure to follow these instructions could
result in death, fire or electrical
shock.
This oven is manufactured with white (neutral)
power supply wire and a cabinet-connected bare
ground wire twisted together.
Feed oven cable through opening in
[] the cabinet. Make electrical connection
following the steps needed for your installation.
1. Disconnect the power supply.
2. Remove the junction box cover.
3. Connect oven cable to junction box through
the U.L.-listed conduit connector.
4. Connect the two black wires together with
twist-on connectors.
5. Connect the two red wires together with twist-
on connectors.
6. Complete electrical connection according to
local codes and ordinances.
cable from
junction
power
supply
box _
rwed
I_
_
blacks
w.hite_
_\
_//"
w're_j¢
\\ /,,<_
grounding oven
,_
cable wires --
_---._
. ....
factory
crimped
b-_q
"-- U.L,-listed
Figure 1
cable from
conduit
oven
connector
If local codes PERMIT
connecting cabinet-ground
conductor to neutral white
wire in junction box:
7. Connect the factory-crimped
bare
and white oven cable wires to the
neutral (white) wire in junction
box, See Figure 1.
8, Replace junction
box cover.
cable from
junction
power supply
Figure 2
If local codes DO NOT
PERMIT connecting
cabinet-ground
conductor
to neutral white wire in
junction box:
7. Separate
the factory-
crimped
bare and white
oven
cable
wires.
8. Connect
white
oven
cable
wire to neutral
(white)
wire
in junction
box, See
Figure 2,
9. Connect the bare
ground
oven cable wire to a
grounded wire in the
junction
box.
See
Figure
2,
IO.
Replace
junction
box
cover,
cable from
connector
oven
If connecting to a
four-wire
electrical
system:
7. Separate
bare and white
oven
cable
wires.
8. Connect
white
oven
cable wire
to neutral
(white) wire in junction
box, See
Figure
2,
9. Connect the bare
ground
oven
cable wire
to the green
ground
wire in junction box,
Do Not connect
bare
ground
wire to neutral
(white) wire in junction
box. See
Figure
2,
IO.
Replace
junction
box
cover,
Attachment
Carefully push against seal area of
oven front frame when pushing oven
into cabinet.
Do Not push against outside edges.
[] Lift oven into cabinet cutout using
the oven opening as an area to grip.
shipping
foot
Push against seal area of front frame to
push oven into cabinet until shipping feet
almost contact cabinet. Use a Phillips
screwdriver to remove screws attaching
shipping feet. Remove and discard shipping
feet.
Push oven completely into cabinet and
center oven in cabinet cutout.
[] Important: Securely fasten oven to
cabinet using the screws provided. Insert the
screws through holes in mounting rails. Do
Not overtighten screws.
Slide top of
trim up.
Push trim
into place.
Replace trim
SCreW.
/
[] Slide top end of each trim upward onto
oven side rails. Push each trim into place at
bottom of trim. Use screws to attach each trim
to oven. Take care not to scratch other
surfaces with ends of trim.
a Replace oven racks.
oven
frame
/hinge
slot
door
hinge
Replace the lower oven door by
inserting ends of hinges into hinge
slots in oven frame. Push behind each hinge
so that hinges are pushed into oven frame as
far as they will go. Open door and remove
both door removal pins. Close and open door
to check that door closes and opens
completely. If door does not close or open
completely, you have not pushed hinges
completely into frame. Repeat door removal
step and reinsert door into hinge slots again.
Check operation
,, Turn on power supply. The
display panel will light up briefly. "PF"
should appear in the temperature display.
\
/
_,
f
ii
BAKE
i BROIL
CLEAN
'\
_
\
)
\
[] Check the operation of your lower
oven. Press the "BROIL" pad. "BROIL" will
appear in the display.
Press the "START" pad. Make sure the
oven door is closed and the "ON" light is
shown in the display area.
After 2 minutes, partially open oven door.
You should feel heat from the oven. Press the
"CANCEL" pad.
If your oven does not heat or an"F" appears
in the display, contact your dealer or check
the "if you need service..." section of this
Installation Instructions.
[] Check the operation of the
microwave oven.
, Fill a microwave-safe container with one cup of
water and place container inside microwave
oven. Close door firmly.
, Set microwave oven cook time to "2:00"
minutes.
, Press the "START/ENTER" pad. The interior
microwave oven light should be on and the
remaining cooking time should be displayed.
• When display reads "1:00," open microwave
oven door. The microwave should stop cooking.
Page 3
• Close door firmly. The interior microwave
oven light should turn off.
• Press the "START/ENTER" pad. Microwave
oven should begin cooking and the
microwave oven interior light should be
On.
• Let microwave oven complete cooking
time. Atone will sound four times at end
of cooking time and microwave oven will
shut off.
• Open microwave oven door and carefully
remove container. Water in container
should be hot.
To get the most efficient use
from your new oven, read your
Use and Care Guide. Keep
Installation
Instructions
and Guide close to oven
for easy reference.