Garmin TREAD Руководство пользователя - Страница 31

Просмотреть онлайн или скачать pdf Руководство пользователя для GPS Garmin TREAD. Garmin TREAD 38 страниц.
Также для Garmin TREAD: Руководство по установке (14 страниц)

Печатать страницу

If using a dampened cloth, turn off the device and disconnect

the device from the power.

Gently wipe the screen with the cloth.

Avoiding theft

• Remove the device and mount from sight when not in use.

• Remove the residue left on the windscreen by the suction

cup.

• Do not keep your unit in the glove compartment.

• Register your device using the Garmin Express software

(garmin.com/express).

Restarting the Device

You can restart your device if it stops functioning.

Hold the power key for 12 seconds.

Removing the Device from the Mount

Press the release tab or button on the mount.

Tilt the top of the device downwards and lift the device from

the mount.

Troubleshooting

My device is not acquiring satellite signals

• Take your device out of multi-storey car parks and away from

tall buildings and trees.

• Remain stationary for several minutes.

My battery does not stay charged for very

long

• Decrease the screen brightness

• Shorten the display timeout

• Decrease the volume

(Adjusting the volume, page

• Turn off the Wi-Fi radio when it is not in use

page

22).

• Put the device in power saving mode when not in use

(Turning the device on or off, page

• Keep your device away from extreme temperatures.

• Do not leave your device in direct sunlight.

My device does not connect to my phone

• Select

> Wireless Networks.

The Bluetooth option must be enabled.

• Enable Bluetooth wireless technology on your phone and

bring your phone within 10 m (33 ft.) of the device.

• Verify your phone is compatible.

Go to

www.garmin.com/bluetooth

• Complete the pairing process again.

To repeat the pairing process, you must unpair your phone

and device

(Disconnecting a Bluetooth device, page

complete the pairing process

Headset, page

13).

My device does not appear as a removable

drive on my computer

On most computers, the device connects using Media Transfer

Protocol (MTP). In MTP mode, the device appears as a portable

device and not as a removable drive.

Troubleshooting

(Display settings, page

22).

1).

‑ Fi settings,

(Wi

1).

for more information.

14) and

(Pairing Your Phone and

My device does not appear as a portable

device on my computer

On Mac

computers and some Windows

connects using USB mass storage mode. In USB mass storage

mode, the device appears as a removable drive or volume, and

not as a portable device. Windows versions prior to Windows XP

Service Pack 3 use USB mass storage mode.

My device does not appear as either a

portable device or a removable drive or

volume on my computer

Disconnect the USB cable from your computer.

Turn off the device.

Connect the USB cable to your device and to a USB port on

your computer.

TIP: the USB cable must connect to a USB port on your

computer, not to a USB hub.

The device turns on automatically and goes into MTP mode or

USB mass storage mode. A picture of the device connected to a

computer appears on the device screen.

NOTE: if you have several network drives mapped on your

computer, Windows may have trouble assigning drive letters to

your Garmin drives. For information about assigning drive

letters, see the help file for your operating system.

Garmin PowerSwitch

Garmin strongly recommends having an experienced installer

22).

with the proper knowledge of electrical systems install the

device. Incorrectly wiring the power cable can result in damage

to the vehicle or the battery and can cause bodily injury.

You can use a connected Garmin PowerSwitch device to control

lights, fans and more from your Tread device.

Mounting Considerations

• The device must be mounted close to the battery and within

the range of the supplied power cable.

• The mounting surface must be strong enough to support the

weight of the device.

• The location must allow room for the routing and connection

of all cables.

Mounting the Device

Before you can mount the device, you must select a mounting

location and purchase the appropriate hardware for your

mounting surface.

Avoid wires, gauges, air bags, air bag covers, heating,

ventilation, and air conditioning and other items when drilling

pilot holes and attaching the mount to the vehicle. Garmin is not

responsible for any damages or consequences arising from the

installation.

Place the mount on the selected location.

computers, the device

Appendix

WARNING

NOTICE