Brother 888-N00 Руководство по эксплуатации - Страница 7
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Швейная машина Brother 888-N00. Brother 888-N00 32 страницы.
Также для Brother 888-N00: Руководство по эксплуатации (32 страниц)
Печатать страницу
2 Changing the initial needle position
You can change the stitch selected when the
machine is turned on to either
(left needle position)" or
(center) needle position)"� (Default:
1
Turn off the machine�
2
Holding down 2, turn on the machine�
3
After the machine has turned on, release 2�
X
The initial needle position is changed�
The currently selected stitch can be confirmed
by the stitch number in the LCD�
3 Turning on/off the operation beep ★
You can turn on/off the operation beep�
(Default: On)
1
Turn off the machine�
2
Holding down 3, turn on the machine�
3
After the machine has turned on, release 3�
The operation beep setting is changed�
X
4 Changing the maximum sewing speed
You can change the maximum sewing speed to
either the standard or slower speed�
(Default: Standard speed mode)
When the slower speed mode is selected, the
maximum speed adjusted with the sewing speed
controller becomes slower� ★
1
Turn off the machine�
2
Holding down 4, turn on the machine�
3
After the machine has turned on, release 4�
The maximum sewing speed is changed�
X
l : Slower speed mode
5 Turning on/off the automatic reverse/
reinforcement stitching
You can set the machine to automatically sew
reverse or reinforcement stitches at the beginning
and end of stitching� (Default: Off)
1
Turn off the machine�
2
Holding down 5, turn on the machine�
3
After the machine has turned on, release 5�
X
The automatic reverse/reinforcement stitching is
turned on or off�
* For details, refer to "Automatic reverse/reinforcement
stitching" (page 17)�
★
: Only for some models�
"straight stitch
"straight stitch (middle
)
: Standard speed mode
l : On
: Off
6 Changing the needle mode
You can change the needle mode to either the
single or twin needle mode�
(Default: Single needle mode)
1
Turn off the machine�
2
Holding down 6, turn on the machine�
3
After the machine has turned on, release 6�
X
The needle mode is changed�
: Single needle mode
* For details, refer to "Sewing with the twin needle" (page
13)�
7 Stitch adjustment ★
With some stitches, a stitch pattern may turn out
poorly depending on the type of fabric� In such a
case, you can make adjustments� (Default: 0)
1
Turn off the machine�
2
Holding down 7, turn on the machine�
3
After the machine has turned on, release 7�
X
The machine turns into the stitch pattern
adjustment mode�
* For details, refer to "Making Adjustment" (page 23)�
Threading the Machine
Winding/Installing the bobbin
CAUTION
• Make sure the power is off while threading
the machine� If you accidentally step on the
foot controller and the machine starts to sew,
you could be injured�
• Be sure to use the
included bobbins
(part code: SA156,
SFB: XA5539-151) or
the same type�
SA156 is Class 15 type bobbin�
1
Pull up the spool pin as far as
possible, and put a spool of
thread on this pin�
CAUTION
• If the spool of thread is not in the right place,
the thread may tangle on the spool pin�
: Twin needle mode
11�5 mm (7/16 inch)
Make sure that the thread
unwinds as shown�
7