Garmin echomap 50 series Руководство пользователя - Страница 21
Просмотреть онлайн или скачать pdf Руководство пользователя для Морская система GPS Garmin echomap 50 series. Garmin echomap 50 series 38 страниц. Flat-mount kit
Также для Garmin echomap 50 series: Краткое руководство по эксплуатации (4 страниц), Руководство пользователя (44 страниц), Руководство пользователя (30 страниц), Руководство по установке (6 страниц), Руководство пользователя (50 страниц), Руководство по установке (6 страниц), Руководство по установке (34 страниц)
Печатать страницу
Radar Display Modes
NOTE: Not all modes are available with all radar devices and all
chartplotters.
Select Radar, and select a mode.
Cruising Mode: Shows a full-screen image of the gathered
radar information.
Harbor Mode: Intended for use in inland waters, this mode
works best with short-range signals (2 nm or less).
Offshore Mode: Intended for use in open waters, this mode
works best with long-range signals.
Sentry Mode: Allows you to put the radar into timed-transmit
mode, in which you can configure a radar transmit and
standby cycle to conserve power. You can also enable a
guard zone in this mode, which identifies a safe zone around
your boat. If you switch from Sentry mode to another mode,
the radar switches to full-time transmission and disables all
guard zones.
Radar Overlay Mode: Shows a full-screen image of the
gathered radar information on top of the Navigation chart.
The Radar overlay displays data based on the most-recently
used radar mode.
Transmitting Radar Signals
NOTE: As a safety feature, the radar enters standby mode after
it warms up. This gives you an opportunity to verify the area
around the radar is clear before beginning radar transmission.
1
With the chartplotter off, connect your radar as described in
the radar installation instructions.
2
Turn on the chartplotter.
The radar warms up and a countdown alerts you when the
radar is ready.
3
Select Radar.
4
Select a radar mode.
A countdown message appears while the radar is starting up.
5
Select Menu > Transmit Radar.
Adjusting the Zoom Scale on the Radar
Screen
The radar zoom scale, also called the radar signal range,
represents the distance from your position (the center) to the
outermost ring.
From a Radar screen, select
Each ring represents an even division of the zoom scale.
For example, if the zoom scale is set at 3 miles, each ring
represents 1 mile from the center out.
Tips for Selecting a Radar Zoom Scale
The radar zoom scale, or radar signal range, indicates the
length of the pulsed signal transmitted and received by the
radar. As the range increases, the radar transmits longer pulses
in order to reach distant targets. Closer targets, especially rain
and waves, also reflect the longer pulses, which can add noise
to the Radar screen. Viewing information about longer-range
targets can also decrease the amount of space available on the
Radar screen for viewing information about shorter-range
targets.
• Determine what information you need to see on the Radar
screen.
For example, do you need information about nearby weather
conditions or targets and traffic, or are you more concerned
about distant weather conditions?
• Assess the environmental conditions where the radar is
being used.
Radar
or
.
Especially in inclement weather, longer-range radar signals
can increase the clutter on the Radar screen and make it
more difficult to view information about shorter-range targets.
In rain, shorter-range radar signals can enable you to view
information about nearby objects more effectively, if the rain
clutter setting is configured optimally.
• Select the shortest effective range, given your reason for
using radar and the present environmental conditions.
Sentry Mode
Sentry mode allows you to put the radar into timed-transmit
mode, in which you can configure a radar transmit and standby
cycle to conserve power. You can also enable a guard zone in
this mode, which identifies a safe zone around your boat and
sounds an alarm when a radar object enters the zone. Sentry
mode works with all Garmin GMR model radars.
Enabling Timed Transmit
Select Radar > Sentry > Menu > Sentry Setup > Timed
Xmit > On.
Setting the Standby and Transmit Times
Before you can set the standby and transmit times, you must
enable timed transmit
(page
To help conserve power, you can indicate the radar standby
time and the transmit time to implement periodic radar signal
transmissions at set intervals.
1
Select Radar > Sentry > Menu > Sentry Setup.
2
Select Stdby Time.
3
Enter the time interval between radar signal transmissions.
4
Select Xmit Time.
5
Enter the duration of each radar signal transmission.
Enabling a Guard Zone
Select Radar > Sentry > Menu > Sentry Setup > Enable
Guard Zone.
Defining a Circular Guard Zone
Before you can define the boundaries of the guard zone, you
must enable a guard zone
You can define a circular guard zone that completely
encompasses your boat.
1
Select Radar > Sentry > Menu > Sentry Setup > Adjust
Guard Zone > Move Radar Guard Zone > Circle.
2
Select the location of the outer guard zone circle.
3
Select the location of the inner guard zone circle to define
the width of the guard zone.
Defining a Partial Guard Zone
You can define the boundaries of a guard zone that does not
completely encompass your boat.
1
Select Radar > Sentry > Menu > Sentry Setup > Adjust
Guard Zone > Move Radar Guard Zone > Corner 1.
2
Touch and drag the location of the outer guard-zone corner
.
3
Select Corner 2.
4
Touch the location of the inner guard-zone corner
define the width of the guard zone.
15).
(page
15).
to
15