Brother MFC-P2000 Руководство по быстрой настройке - Страница 41
Просмотреть онлайн или скачать pdf Руководство по быстрой настройке для Принтер "все в одном Brother MFC-P2000. Brother MFC-P2000 43 страницы. Laser printer / scanner / copier
Печатать страницу
Declaration of Conformity (For Europe)
We, Brother International Europe Ltd.,
Brother House 1 Tame Street, Guide Bridge,
Audenshaw, Manchester M34 5JE, UK.
declare that this product is in conformity with the following
normative documents.
Safety: EN 60950,
EMC:
EN 55022 Class B,
following the provisions of the Low Voltage Directive 73/23/EEC
and the Electromagnetic Compatibility Directive 89/336/EEC (as
amended by 91/263/EEC and 92/31/EEC).
Issued by:
Brother International Europe Ltd.
European Technical Services Division
IEC 825 Specification
This machine is a Class 1 laser product as defined in IEC 825
specifications. The label shown below is attached in countries
where required.
CLASS 1LASER PRODUCT
APPAREIL Å LASER DE CLASSE 1
LASER KLASSE 1 PRODUKT
This machine has a Class 3B Laser Diode which emits invisible
laser radiation in the Scanner Unit. The Scanner Unit should not be
opened under any circumstances.
Caution
Use of controls, adjustments or performance of procedures other
than those specified in this manual may result in hazardous radiation
exposure.
The following caution label is attached near the scanner unit.
CAUTION
INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED.
AVOID DIRECT EXPOSURE TO BEAM. CLASS 3B LASER PRODUCT.
ADVARSEL
USYNLIG LASER STRÅLING NÅR KABINETLÅGET STÅR ÅBENT.
UNGDÅ DIREKTE UDSÆTTELSE FOR STRÅLING. KLASSE 3B LASER.
VARNING
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRRAR
ÄR URKOPPLADE. STRÅLEN ÄR FARLIG. KLASS 3B LASER APPARAT.
VARO!
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA
NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN. LUOKAN
3B LASERLAITE.
ADVARSEL
USYNLIG LASERSTRÅLING.UNNGÅ DIREKTE KONTAKT MED LASERENHETEN
NÅR TOPPDEKSELET ER ÅPENT. KLASSE 3B LASERPRODUKT.
ATTENTION
RADIATIONS LASER INVISIBLES QUANDOUVERT ET VERROUILLAGE ENLEVE.
EVITER EXPOSITIONS DIRECTES AU FAISCEAU. PRODUIT LASER CLASSE 3B.
VORSICHT
UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG
GEÖFFENT UND SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN.
SICHERHEITSKLASSE 3B.
ATENCIÓN
RADIACIÓN LASER INVISIBLE CUANDO SE ABRE
LA TAPA Y EL INTERRUPTOR INTERNO ESTÁ
ATASCADO. EVITE LA EXPOSICIÓN DIRECTA
DE LOS OJOS. PRODUCTO LASER CLASE 3B.
For Finland and Sweden
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
Varoitus! Laitteen käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1
ylittävälle näkymättömälle lasersäteilylle.
Varning – Om apparaten används på annat sätt än i denna
Bruksanvisning specificerats, kan användaren utsättas för osynlig
laserstrålning, som överskrider gränsen för laserklass1.
Geräuschemission / Acoustic Noise Emission
(For Germany Only)
Lpa < 70 dB (A) DIN 45635-19-01-KL2
This product is designed for use in a
professional environment.
EN 60825
EN 50082-1
(For 220–240 V Model Only)
IMPORTANT - For Your Safety
To ensure safe operation the three-pin electrical plug supplied
must be inserted only into a standard three-pin power point which
is properly grounded through normal household wiring.
Extension cords used with the equipment must be three-pin plug
type and correctly wired to provide proper grounding. Incorrectly
wired extension cords may cause personal injury and equipment
damage.
The fact that the equipment operates satisfactorily does not imply
that the power is grounded and that the installation is completely
safe. For your safety, if in any doubt about the effective
grounding of the power, consult a qualified electrician.
Disconnect device
This machine must be installed near a power outlet, which is
easily accessible. In case of emergencies, you must disconnect the
power cord from the power outlet in order to shut off power
completely.
IMPORTANT - Wiring Information
If the power cord supplied with this machine is not suitable for
your electrical outlet, remove the plug from the mains cord and fit
an appropriate three pin plug. If the replacement plug is intended
to take a fuse then fit the same fuse as the original.
If a moulded plug is severed from the power cord then it should
be destroyed because a plug with cut wires is dangerous if
plugged into a live socket outlet. Do not leave it where a child
might find it.
In the event of replacing the plug fuse, fit a fuse approved by
ASTA to BS1362 with the same rating as the original fuse.
Always replace the fuse cover. Never use a plug with the cover
omitted.
WARNING - THIS MACHINE MUST BE PROPERLY
EARTHED.
The wires in the mains cord are coloured in accordance with the
following code:
Green and yellow:
Blue:
Brown:
The colours of the wiring in the power lead of this machine may
not correspond with the markings which identify the terminals in
your plug. If you need to fit a different plug, proceed as follows.
Remove a length of the cord outer sheath, taking care not to
damage the coloured insulation of the wires inside.
Cut each of the three wires to the appropriate length. If the
construction of the plug permits, leave the green and yellow wire
longer than the others so that, in the event that the cord is pulled
out of the plug, the green and yellow wire will be the last to
disconnect.
Remove a short section of the coloured insulation to expose the
wires.
The wire which is coloured green and yellow must be connected
to the terminal in the plug which is marked with the letter "E" or
by the earth symbol or coloured green or green and yellow.
The wire which is coloured blue must be connected to the
terminal which is marked with the letter "N" or coloured black or
blue.
The wire which is coloured brown must be connected to the
terminal which is marked with the letter "L" or coloured red or
brown.
The outer sheath of the cord must be secured inside the plug. The
coloured wires should not hang out of the plug.
(For U.K. only)
Ground
Neutral
Live