Fujitsu UTY-VDGX Руководство по установке - Страница 2
Просмотреть онлайн или скачать pdf Руководство по установке для Кондиционер Fujitsu UTY-VDGX. Fujitsu UTY-VDGX 19 страниц. Airstage
Печатать страницу
INSTALLATION MANUAL
PART NO. 9381279005
VRF system DX-kit
Contents
1.
SAFETY PRECAUTIONS .........................................................................................1
2.
ABOUT THIS PRODUCT ..........................................................................................1
2.1. Precautions for using R410A refrigerant ............................................................1
2.2. Special tool for R410A ........................................................................................1
2.3. Accessories ........................................................................................................2
2.4. Optional parts .....................................................................................................3
3.
PRODUCT SELECTION ...........................................................................................3
3.1. Product Lineup ...................................................................................................3
3.2. System Design ...................................................................................................3
4.
INSTALLATION WORK ............................................................................................4
4.1. Selecting an installation location ........................................................................4
4.2. Installation dimensions .......................................................................................4
4.3. Installing the unit .................................................................................................4
5.
PIPE INSTALLATION ...............................................................................................6
5.1. Selecting the pipe material .................................................................................6
5.2. Pipe requirement ................................................................................................6
5.3. Bending pipes .....................................................................................................6
5.4. Pipe connection ..................................................................................................6
5.5. Installing heat insulation .....................................................................................7
6.
MOUNTING THERMISTORS ....................................................................................7
7.
ELECTRICAL WIRING..............................................................................................7
7.1. Electrical requirement .........................................................................................8
7.2. Wiring method ....................................................................................................8
7.3. Unit wiring ...........................................................................................................8
7.4. Connection of wiring .........................................................................................10
7.5. External input and external output (Optional parts) ..........................................12
8.
FIELD SETTING ......................................................................................................15
8.1. Setting the address ...........................................................................................15
8.2. Dip switch setting ..............................................................................................16
8.3. Function setting ................................................................................................16
9.
TEST RUN ...............................................................................................................17
9.1. Test run using Outdoor unit (PCB) ...................................................................17
9.2. Test run using remote controller .......................................................................17
10. CHECK LIST (Example) .........................................................................................17
11. ERROR CODES ......................................................................................................17
12. OPERATIONS .........................................................................................................18
12.1. Analog external inputs ....................................................................................18
1. SAFETY PRECAUTIONS
• Be sure to read this Manual thoroughly before installation.
• The warnings and precautions indicated in this Manual contain important information per-
taining to your safety. Be sure to observe them.
• Hand this Manual, to the customer. Request the customer to keep them on hand for future
use, such as for relocating or repairing the unit.
• For installation of the air handling unit (heat exchanger), refer to the installation manual
for the air handling unit.
This mark indicates procedures which, if improperly
WARNING
performed, might lead to the death or serious injury of the
user.
Request your dealer or a professional installer to install the DX-kit in accordance with
this Installation Manual. An improperly installed unit can cause serious accidents such
as water leakage, electric shock, or fi re. If the DX-kit is installed in disregard of the
instructions in the Installation Manual, it will void the manufacturer's warranty.
Do not turn ON the power until all work has been completed. Turning ON the power
before the work is completed can cause serious accidents such as electric shock or
fi re.
If refrigerant leaks while work is being carried out, ventilate the area. If the refrigerant
comes in contact with a fl ame, it produces a toxic gas.
Installation work must be performed in accordance with national wiring standards by
authorized personnel only.
Except for EMERGENCY, never turn off main as well as sub breaker of the DX-kits
during operation. It will cause compressor failure as well as water leakage. First, stop
the DX-kit by operating the control unit, converter or external input device and then cut
the breaker.
Make sure to operate through the control unit, converter or external input device.
When the breaker is designed, locate it at a place where the users cannot start and
stop in the daily work.
En-1
This mark indicates procedures which, if improperly performed,
CAUTION
might possibly result in personal harm to the user, or damage to
property.
Read carefully all security information before use or install the DX-kit.
Do not attempt to install the DX-kit or a part of the DX-kit by yourself.
This unit must be installed by qualified personnel with a capacity certificate for handling
refrigerant fluids. Refer to regulation and laws in use on installation place.
The installation must be carried out in compliance with regulations in force in the place
of installation and the installation instructions of the manufacturer.
This unit is part of a set constituting the DX-kit. It must not be installed alone or with non-
authorized by the manufacturer.
Always use a separate power supply line protected by a circuit breaker operating on all
wires with a distance between contact of 3mm for this unit.
The unit must be correctly earthed (grounded) and the supply line must be equipped with
a differential breaker in order to protect the persons.
The units are not explosion proof and therefore should not be installed in explosive
atmosphere.
Never touch electrical components immediately after the power supply has been turned
off. Electric shock may occur. After turning off the power, always wait 5 minutes before
touching electrical components.
This unit contains no user-serviceable parts. Always consult authorized service
personnel to repairs.
When moving, consult authorized service personnel for disconnection and installation of
the unit.
2. ABOUT THIS PRODUCT
2.1. Precautions for using R410A refrigerant
Do not introduce any substance other than the prescribed refrigerant into the
refrigeration cycle. If air enters the refrigeration cycle, the pressure in the refrigeration
cycle will become abnormally high and cause the piping to rupture.
If there is a refrigerant leak, make sure that it does not exceed the concentration limit.
If a refrigerant leak exceeds the concentration limit, it can lead to accidents such as
oxygen starvation.
Do not touch refrigerant that has leaked from the refrigerant pipe connections or other
area. Touching the refrigerant directly can cause frostbite.
If a refrigerant leak occurs during operation, immediately vacate the premises and
thoroughly ventilate the area. If the refrigerant comes in contact with a flame, it
produces a toxic gas.
2.2. Special tool for R410A
To install a unit that uses R410A refrigerant, use dedicated tools and piping materials
that have been manufactured specifically for R410A use. Because the pressure
of R410A refrigerant is approximately 1.6 times higher than the R22, failure to
use dedicated piping material or improper installation can cause rupture or injury.
Furthermore, it can cause serious accidents such as water leakage, electric shock, or
fi re.
Tool name
The pressure in the refrigerant system is extremely high
and cannot be measured with a conventional gauge.
To prevent erroneous mixing of other refrigerants,
the diameter of each port has been changed. It is
Gauge manifold
recommended to use a gauge manifold with a high
pressure display range of -0.1 to 5.3 MPa and a low
pressure display range of -0.1 to 3.8 MPa.
To increase pressure resistance, the hose material and
base size were changed.
Charging hose
(The charging port thread diameter for R410A is 1/2 UNF
20 threads per inch.)
A conventional vacuum pump can be used by installing a
vacuum pump adapter.
Be sure that the pump oil does not backflow into the
Vacuum pump
system. Use one capable for vacuum suction of
-100.7 kPa (5 Torr, -755 mmHg).
Special gas leakage detector for R410A refrigerant.
Gas leakage detector
WARNING
WARNING
Changes