Fujitsu LifeBook B6110D Руководство по биосфере - Страница 2
Просмотреть онлайн или скачать pdf Руководство по биосфере для Ноутбук Fujitsu LifeBook B6110D. Fujitsu LifeBook B6110D 27 страниц. Lifebook b series
Также для Fujitsu LifeBook B6110D: Руководство по биосфере (38 страниц), Руководство по началу работы (2 страниц)
Печатать страницу
L i f e B o o k B S e r i e s N o t e b o o k B I O S
B Series BIOS
BIOS SETUP UTILITY
The BIOS Setup Utility is a program that sets up the
operating environment for your notebook. Your BIOS
is set at the factory for normal operating conditions,
therefore there is normally no need to set or change the
BIOS environment to operate your notebook.
The BIOS Setup Utility configures:
• Device control feature parameters, such as changing
I/O addresses and boot devices.
• System Data Security feature parameters, such as
passwords.
Entering the BIOS Setup Utility
To enter the BIOS Setup Utility do the following:
1. Turn on or restart your notebook.
F2
2. Press the [
] key once the Fujitsu logo appears on
the screen. This will open the main menu of the
BIOS Setup Utility with the current settings
displayed.
3. Press the arrow keys to scroll through the other
setup menus to review or alter the current settings.
Navigating through the Setup Utility
The BIOS setup utility consists of six menus; Main,
Advanced, Security, Boot, Info and Exit. This document
explains each menu, including all submenus and setup
items.
The following procedures allow you to navigate the setup
utility menus:
1. To select a menu, use the cursor keys: [
2. To select a field within a menu or a submenu, use the
cursor keys: [ ], [
3. To select the different values for each field, press the
Spacebar
+
[
] or [
] to change to the next higher selec-
F5
tion and [
] or [-] to go to the next lower selection.
4. To activate a submenu press the [Enter] key.
5. To return to a menu from a submenu, press
Esc
the [
] key.
6. To go to the Exit menu from any other menu,
Esc
press the [
] key.
2
],[
].
• Selecting a field causes a help message
• Pressing the Enter key with the highlight
7. Pressing the [
the default values.
8. Pressing the [
tion and exits the BIOS Setup Utility. You will be
asked to verify this selection before it is executed.
9. Pressing the [
Entering the Setup Utility After a Configuration
Change or System Failure
If there has been a change in the system configuration
that does not match the parameter settings stored
in your BIOS memory, or there is a failure in the system,
the system beeps and/or displays an error message after
the Power On Self Test (POST). If the failure is not
too severe, it will give you the opportunity to modify
the settings of the setup utility, as described in the
following steps:
1. When you turn on or restart the computer there is
a beep and/or the following message appears on
the screen:
Error message - please run SETUP
program Press <F1> key to continue,
<F2> to run SETUP
].
2. If an error message is displayed on the screen, and
you want to continue with the boot process and start
the operating system anyway, press the [
3. If an error message is displayed on the screen, and
you want to enter the setup utility, press the [
4. When the setup utility starts with a fault present, the
system displays the following message:
Warning!
Error message
[Continue]
5. Press any key to enter the setup utility. The system
will then display the Main Menu with current
parameters values.
about the field to be displayed on the
right-hand side of the screen.
on a selection that is not a submenu or
auto selection will cause a list of all
options for that item to be displayed.
Pressing the Enter key again will select
the highlighted choice.
F9
] key resets all items in the BIOS to
F10
] key saves the current configura-
F1
] key gives you a general help screen.
F1
] key
.
F2
] key.