Indesit D2FHK26B Ежедневное справочное руководство - Страница 2

Просмотреть онлайн или скачать pdf Ежедневное справочное руководство для Посудомоечная машина Indesit D2FHK26B. Indesit D2FHK26B 17 страниц.

Печатать страницу

FIRST TIME USE

SALT, RINSE AID AND DETERGENT

ADVICE REGARDING THE FIRST TIME USE

After installation, remove the stoppers from the racks and the retaining

elastic elements from the upper rack.

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes and

on the machine's functional components.

• It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.

• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher

(see PRODUCT DESCRIPTION) and must be filled when the SALT REFILL

indicator light

in the control panel is lit.

1. Remove the lower rack and unscrew the

reservoir cap (anticlockwise).

2. Only the first time you do this: fill the salt

reservoir with water.

3. Position the funnel (see figure) and fill the salt

reservoir right up to its edge (approximately

1 kg); it is not unusual for a little water to leak

out.

4. Remove the funnel and wipe any salt residue

away from the opening.

Make sure the cap is screwed on tightly, so that no detergent can get

into the container during the wash program (this could damage the

water softener beyond repair).

Whenever you need to add salt, it is mandatory to complete the

procedure before the beginning of the washing cycle to avoid corrosion.

SETTING THE WATER HARDNESS

To allow the water softener to work in a perfect way, it is essential that

the water hardness setting is based on the actual water hardness in

your house. This information can be obtained from your local water

supplier.

The factory sets the default value for the water hardness

• Switch on the appliance by pressing the ON/OFF button.

• Switch off the appliance by pressing the ON/OFF button.

• Hold down button START/Pause for 5 seconds.

• Switch on the appliance by pressing the ON/OFF button.

• The ON/OFF LED light will flash as many times as the level that was set.

• Set the desired water hardness level using the PROGRAM SELECTION

knob (see WATER HARDNESS TABLE).

Water Hardness Table

Level

German

degrees

Soft

Medium

Average

Hard

Very hard

• Switch off the appliance by pressing the ON/OFF button.

Setting is complete!

As soon as this procedure is complete, run a program without loading.

Only use salt that has been specifically designed for dishwashers.

After the salt has been poured into the machine, the SALT REFILL indi-

cator light switches off.

If the salt container is not filled, the water softener and the heating

element may be damaged as a result of limescale accumulation.

Using of Salt is recommended with any type of dishwasher detergent.

°dH

°fH

French

degrees

0 - 6

0 - 10

7 - 11

11 - 20

12 - 16

21 - 29

17 - 34

30 - 60

35 - 50

61 - 90

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse aid dispenser A should be

filled when when the dark optical indicator on the dispenser door C

becomes transparent.

1. Open the dispenser B by pressing and pulling up the tab on the lid.

2. Pour in the rinse aid (max.110 ml), making sure it does not overflow

from the dispenser. If this happens, clean the spill immediately with

a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

ADJUSTING THE DOSAGE OF RINSE AID

If you are not completely satisfied with the drying results, you can ad-

just the quantity of rinse aid used.

• Switch the dishwasher on using the ON/OFF button.

• Switch it off using the ON/OFF button.

• Press button START/Pause three times.

• Switch it on using the ON/OFF button.

• The START/Pause LED light will flash as many times as the level that

was set.

• Set the level of rinse aid quantity to be supplied using the PROGRAM

SELECTION knob (see PROGRAMS TABLE).

• Switch it off using the ON/OFF button

Setting is complete!

If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied.

A maximum of 5 levels can be set according to the dishwasher model.

The factory setting is specific to the model, please follow instruction

above to check this for your machine.

• If you see bluish streaks on the dishes, set a low number (2-3).

• If there are drops of water or limescale marks on the dishes,

set a mid-range number (4-5).

FILLING THE DETERGENT DISPENSER

°Clark

To open the detergent dispenser use the opening device D.

English

Introduce the detergent into the dry dispenser E only. Place the

degrees

amount of detergent for pre-washing directly inside the tub.

0 - 7

8 - 14

15 - 20

21 - 42

43 - 62

The detergent dispenser automatically opens up at the right time

according to the program.

Usage of detergent not designed for dishwashers may cause mal-

function or damage to the appliance.

1. When measuring out the detergent

refer to the mentioned earlier infor-

mation to add the proper quantity.

Inside the dispenser E there are

indications to help the detergent

dosing.

2. Remove detergent residues from

the edges of the dispenser and clo-

se the cover until it clicks.

3. Close the lid of the detergent

dispenser by pulling it up until the

closing device is secured in place.