AC Tech SCF SERIES Инструкции - Страница 2

Просмотреть онлайн или скачать pdf Инструкции для Клавиатура AC Tech SCF SERIES. AC Tech SCF SERIES 2 страницы. Remote keypad
Также для AC Tech SCF SERIES: Краткое справочное руководство (2 страниц)

5.
SETTING UP THE SCF DRIVE
There are three possible control scenarios when using the remote
keypad:
1. The remote keypad is used for Start/Stop control, Forward/Reverse
selection, programming, and monitoring.
2. The remote keypad is used for programming and monitoring, but
the drive's terminal strip is used for Start/Stop control and Forward/
Reverse selection.
3. The remote keypad is used for programming and monitoring, while
Start/Stop control and Forward/Reverse selection can be toggled
between the remote keypad and the drive's terminal strip.
In all of the above scenarios, speed is controlled from the remote keypad
unless another speed reference source is selected.
Note 1:
The STOP key on the remote keypad will work even if the terminal strip
is used for Start/Stop control
1. REMOTE KEYPAD TO PROGRAM, MONITOR AND CONTROL
a. Set Parameter 14 (CONTROL) to "02" (REMOTE KEYPAD ONLY).
b. Install a jumper between terminal TB-1 and TB-2 on the drive's
terminal strip.
2. REMOTE KEYPAD TO PROGRAM AND MONITOR, AND
TERMINAL STRIP TO CONTROL.
a. Set Parameter 14 (CONTROL) to "03" (TERMINAL STRIP OR
REMOTE KEYPAD).
b. Wire the Start/Stop and Forward/Reverse circuits to the drive's
terminal strip according to the SCF manual.
6.
REMOTE KEYPAD FUNCTIONS
The M key and the s and t keys on the remote keypad function the
same as the Mode button and the s and t buttons on the drive. The
other remote keypad functions are described below:
Reverse/Forward key: Selects Forward or Reverse direction.
The R/F key is only active if Parameter 17 - ROTATION is
R F
set to "2" (FORWARD AND REVERSE).
When the R/F key is pressed, the symbol for the opposite
direction will blink on the display. Press the M key within
four seconds to confirm the rotation change.
Below are the display symbols used to indicate direction:
FORWARD
RUN key: Press RUN to Start the drive. The RUN key is
only active if the remote keypad is selected as the Start/Stop
control source.
RUN
STOP key: Press STOP to Stop the drive. The STOP key
is active whenever the remote keypad is operational, even
if the remote keypad is only used for programming and
STOP
monitoring.
WARNING!
If the remote keypad display is totally blank or is displaying a "JF" fault,
the STOP key WILL NOT stop the drive. The remote keypad must be
operational in order for the STOP key to be active
REVERSE
3. TOGGLE CONTROL BETWEEN REMOTE KEYPAD AND
TERMINAL STRIP
a. Set Parameter 14 (CONTROL) to "03" (TERMINAL STRIP OR
REMOTE KEYPAD).
b. Choose either Terminal 13A or 13C on the drive as the input that will
toggle between remote keypad control and terminal strip control.
To use TB-13A, set Parameter 10 (TB-13A FUNCTION SELECT) to
"08" (REMOTE KEYPAD).
To use TB-13C, set Parameter 12 (TB-13C FUNCTION SELECT) to
"07" (REMOTE KEYPAD).
c. Wire a selector switch or relay contact between TB-13A or TB-13C
(whichever was programmed for REMOTE KEYPAD in Step b above)
and TB-2 on the drive's terminal strip.
d. Wire the Start/Stop and Forward/Reverse circuits to the drive's
terminal strip according to the SCF manual.
If a 2-wire Start/Stop circuit is required, use the Alternate 2- Wire
circuit described in Section 11.3 of the SCF manual.
To select the Remote Keypad as the control source, close TB-13A or TB-
13C (whichever was programmed for REMOTE KEYPAD) to TB-2.
To select the terminal strip as the control source, open TB-13A or TB-13C
with respect to TB-2.
Note 2:
When the remote keypad is selected for Start/Stop control, terminal
TB-1 on the SCF drive must be closed to TB-2 to allow the drive to run.
TB-1 is a Stop input and it is always active. If it is open with respect to
TB-2, the drive will not run.
7.

TROUBLESHOOTING

CONDITION / DISPLAY
Remote Keypad display
Parameter 14 - CONTROL is set to "01"
is blank.
(TERMINAL STRIP ONLY). See Section 5.
The Remote Keypad is not wired correctly
to the drive. See Section 4.
Remote Keypad and/
"JF" typically indicates a communication
or SCF drive displays
problem. Check for proper wiring between
"JF".
the remote keypad and the drive. A "JF"
fault can also occur due of the following:
- Attempting to start the drive from the
Remote Keypad and TB-1 is not closed to
TB-2. See NOTE 2 in Section 5
- Attempting to power the Remote Keypad
and an auxiliary relay from TB-11. See
NOTE 2 in Section 4.
The RUN key does not
To start the drive using the RUN key, the
work to start the drive.
Remote Keypad must be selected as the
control source, and TB-1 must be closed to
TB-2 on the drive's terminal strip.
The R/F key does not
To use the R/F key to change rotation
work to change rotation
direction, the Remote Keypad must be
direction.
selected as the control source, Parameter
17 - ROTATION must be set to "02"
(FORWARD AND REVERSE), and the M
key must be pressed with 4 seconds to
confirm the change. See Section 6.
(KF01G)
POSSIBLE CAUSES