Indesit ISL60V Буклет с инструкциями - Страница 7

Просмотреть онлайн или скачать pdf Буклет с инструкциями для Сушилка Indesit ISL60V. Indesit ISL60V 16 страниц. Indesit tumble dryer instruction booklet

Печатать страницу

The Controls

PROGRAMMES knob

! Warning, if after pressing the start button, the

programmes knob position is changed, the new

position will NOT change the programme selected.

! Position 0, turning the knob to position 0 resets

and cancels a programme.

OPTION buttons / lights

These buttons are used to customise the selected

programme to your requirements. A programme must

have been selected on the programme knob before

an option can be selected. Not all options are available

for all programmes (see Start and Programmes). If an

option is not available and you press the button, the

buzzer will beep four times. If the option is

available there will be one beep and the option light

above the button lights to confirm the selection.

After the start button has been pressed only the

Alarm option can be changed.

Progress (Drying, Cool Tumble, Post Creasecare) /

Delay (3hr 6hr 9hr 12hr) Lights

When the light above the delay button is on, these lights

flash to indicate the delay time is selected. During other

programmes they indicate the progress of the dryer,

each one comes on as the corresponding phase starts.

Time Delay

The start of some programmes (see Start and

Programmes) can be delayed for up to 12 hours in

3hr steps.

When a delayed start is in progress the light above the

delay button will be on and the selected delay period

light will flash (after the start button has been pressed).

To set a delayed start, press the Time Delay button,

and the light above the button will come on together

with the 3hr delay light. Pressing the button again will

advance the delay setting to 6hr, the 3hr light goes

out and the 6hr light is on. Each time you press the

button the delay setting advances 3 hours, as indicated

by the corresponding light. If the 12hr light is on,

pressing the button again will cancel the delay.

You can also cancel the delay by turning the

programmes knob to 0, wait for the buzzer to beep

and then turn back to your selected programme.

Pre Creasecare

When a delayed start has been selected, the clothes

are tumbled occasionally during the delayed period

to help prevent creases developing.

High Heat

When available this button selects high heat. Press this

button and a high heat setting is selected and the light

above the button comes on. Timed programmes

have a default of low heat, if the light alongside the

button is on then pressing the button selects a low

heat setting and the light goes out.

Alarm

Available on all programmes and allows the buzzer

to give a signal at the end of the drying cycle, to

remind you that the clothes are ready to be removed.

Press the button and the light will show that the

option is selected.

Post Creasecare

The clothes are occasionally tumbled after the end of

the drying and cool tumble cycles, to help prevent

creases developing should you not be available to

remove the load immediately the programme is com-

plete.

Door Opening

Opening the door during a programme will stop the

dryer and have the following effects:

All 3 progress lights and the 3hr delay light come

on.

During a delay phase the delay will continue to

count down. The start button must be pressed to

resume the delay programme.

One of the delay lights will flash to show the

current delay setting.

The start button must be pressed to resume the

programme. The progress lights will change to

show the current status.

During the cool tumble or post creasecare phase

of a drying programme and anytime during an

Airing or Cool Tumble programme, the programme

will finish. Pressing the start button will re-start a

new programme at the beginning.

Changing the programmes knob will select a

new programme, after you press the start button.

You can use this to select the Cool Tumble

programme to cool the clothes, if you find them

dry enough.

Note

If you have a power cut, switch off the power or

remove the plug, press the START button and the

programme will resume.