Kohler Command Pro CH960 Руководство пользователя - Страница 5
Просмотреть онлайн или скачать pdf Руководство пользователя для Двигатель Kohler Command Pro CH960. Kohler Command Pro CH960 21 страница. Horizontal/vertical shaft
Также для Kohler Command Pro CH960: Руководство пользователя (8 страниц)
Печатать страницу
Fuel Recommendations
WARNING: Explosive Fuel!
Gasoline is extremely flammable and its vapors can explode if
ignited. Store gasoline only in approved containers, in well
ventilated, unoccupied buildings, away from sparks or flames.
Do not fill the fuel tank while the engine is hot or running,
since spilled fuel could ignite if it comes in contact with hot
parts or sparks from ignition. Do not start the engine near
spilled fuel. Never use gasoline as a cleaning agent.
General Recommendations
Purchase gasoline in small quantities that can be used
within 30 days and store only in clean, approved
containers. Do not use gasoline left over from the
previous season unless treated with a fuel stabilizer
(refer to Storage), to minimize gum deposits and
ensure easy starting. Do not use gasoline containing
Methanol, or add oil to the gasoline.
Do not overfill the fuel tank. Leave room for the fuel to
expand.
Fuel Type
For best results use only clean, fresh, unleaded
gasoline with a pump sticker octane rating of 87 or
higher. In countries using the Research method, it
should be 90 octane minimum.
Unleaded gasoline is recommended as it leaves less
combustion chamber deposits and reduces harmful
exhaust emissions. Leaded gasoline is not
recommended and must not be used in any models
where exhaust emissions are regulated.
Gasoline/Alcohol blends
Gasohol (up to 10% ethyl alcohol, 90% unleaded
gasoline by volume) is approved as a fuel for Kohler
engines. Other gasoline/alcohol blends including E20
and E85 are not to be used and not approved. Any
failures resulting from use of these fuels will not be
warranted.
Gasoline/Ether blends
Methyl Tertiary Butyl Ether (MTBE) and unleaded
gasoline blends (up to a maximum of 15% MTBE by
volume) are approved as a fuel for Kohler engines.
Other gasoline/ether blends are not approved.
Engine Identification Numbers
When ordering parts, or in any communication
involving an engine, always give the Model,
Specification, and Serial Numbers of the engine.
The engine identification numbers appear on a decal
affixed to the engine shrouding. Include letter suffixes,
if there are any.
Record your engine identification numbers on the
identification label below (Figure 4) for future reference.
IMPORTANT ENGINE INFORMATION
THIS ENGINE MEETS EMISSION REGS FOR U.S. EPA PH 2 SMALL
OFF–ROAD ENGINES AND CA 2006 AND LATER LSI ENGINES
FAMILY
DISPL. (CC)
MODEL NO.
SPEC. NO.
SERIAL NO.
BUILD DATE
OEM PROD. NO.
EMISSION COMPLIANCE PERIOD:
EPA:
CERTIFIED ON:
REFER TO OWNER'S MANUAL FOR HP RATING, SAFETY,
MAINTENANCE AND ADJUSTMENTS
1-800-544-2444 www.kohlerengines.com
KOHLER CO. KOHLER, WISCONSIN USA
IMPORTANT ENGINE INFORMATION
THIS ENGINE MEETS EMISSION REGS FOR U.S. EPA 2006 AND
LATER AND EC STAGE II (SN:4) SI SMALL OFF–ROAD ENGINES
AND CA 2006 AND LATER LSI ENGINES
FAMILY
TYPE APP
DISPL. (CC)
MODEL NO.
SPEC. NO.
SERIAL NO.
BUILD DATE
OEM PROD. NO.
EMISSION COMPLIANCE PERIOD:
EPA:
CERTIFIED ON:
REFER TO OWNER'S MANUAL FOR HP RATING, SAFETY,
MAINTENANCE AND ADJUSTMENTS
1-800-544-2444 KohlerEngines.com
KOHLER CO. KOHLER, WISCONSIN USA
Figure 4. Engine Identification Label.
The Emission Compliance Period referred to on the
Emission Control or Air Index label indicates the
number of operating hours for which the engine has
been shown to meet Federal emission requirements.
The following table provides the Engine Compliance
Period (in hours) associated with the category
descriptor found on the certification label.
Emission Compliance Period (Hours)
Category A
EPA
1000 hours
Refer to certification label for engine displacement.
Exhaust Emission Control System for models CH940-
CH1000 is EM.
Model Designation
Model CH980 for example: C designates Command
engine, H designates horizontal crankshaft, and 980
indicates the numerical model designation. A letter
suffix designates a specific version as follows:
Suffix
Designates
S
Electric Start
5