AVM EVOLUTION A2 Руководство по эксплуатации - Страница 6
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Усилитель AVM EVOLUTION A2. AVM EVOLUTION A2 9 страниц. Integrated amplifier
Печатать страницу
To ensure that all sources are adjusted to the same loudness first select a medium-loud source using the
switch PROGRAM (3). This source will be the reference for comparisons. Adjust the loudness with the
VOLUME button (9) until a pleasant volume is reached. With the switch PROGRAM (3) select another sour-
ce and press the button LEVEL (7).Adjust the VOLUME button (9) until the loudness of this source matches
that of the reference source. Continue these operations until all signal sources have been satisfactorily set.
After this process has been successfully completed press the button LEVEL (7) anew. All settings are now
saved and you can use the VOLUME button (9) to carry out any further adjustments manually.
TAPE RECORDING
If a tape recorder is connected to theA2 you can record whichever source you have selected with the switch
PROGRAM (3). The recording level is independent of the volume and balance settings.
MONITORING
To check the quality of the recording you can activate the monitor function. Provided the A2 unit is swit-
ched on the monitor function can be activated by pressing the toggle switch MON (4). The outputs (loud-
speaker (11.23), headphones (10) and PRE OUT (22)) receive the incoming signal from the connected tape
recorder for background monitoring. Monitoring operation is shown in the display (6). The selected setting
remains until the toggle switch MON (4) is pressed anew. Further information to this mode of operation can
be found in the operational manual of your recorder under the headings "Background monitoring" or
"Monitor",
TIP
The A2 possesses "intelligent" monitoring circuitry which hinders simultaneous monitor operation when
TAPE is selected. Feedback would otherwise occur.
TAPE PLAYBACK
If you wish to listen to a tape recording set the switch PROGRAM (3) to TAPE. This is shown in the -
display (6).
OPERATION OF TONAL PROCESSORS/EQUALIZERS
When the A2 unit is switched on and the toggle switch PROCESSOR
(5)
has been pressed the processor is
activated. This influences the output signal of the A2 (loudspeakers (11.23) and PRE OUT
(22)).
The tape
recording signai (socket 19) remains uninfiuenced.Activation of the processor is shown in the display (6).The
selected setting is retained until the toggie switch PROC
(5)
is pressed again.
26
HEADPHONES OPERATION
Stereo headphones can be used with the A2. These utilize a 6.3mm headphone socket. As long as the head-
phones are connected the outputs (loudspeakers (11,23) and PRE OUT (22)) are automatically switched off.
The tape recording output remains active.
If your headphones are not equipped with a suitable plug you will need an adapter.
REMOTE CONTROL OF THE EVOLUTION A2 (OPTIONAL)
A system remote control is available with which you can operate all the functions of your integrated ampli-
fier from the comfort of your place of listening. The desired functions can be activated by pressing the rele-
vant button on the remote control transmitter (see the remote control diagram above).
Some buttons have a dual role to permit comfortable operation. The "ON" button permits the switch bet-
ween "Standby" and "On". Alternativeiy, with the unit already operational, it allows you to switch between,
or leave, the next menu leveL The "VOLUME -" and the "VOLUME +" buttons can be used to move the cur-
sor arrow in the sub menus. They can also be used to set the balance (sub menu "bal") and input sensitivity
(submenu "set").
Always point the remote control transmitter at the display (6) of the A2 unit. This is where the IR-receiver
is located.
TIP
The selection "stand by" is available to mute the integrated amplifier temporarily, for example to make a tele-
phone calL "Standby" condition is no replacement for switching off the unit. In stand by mode the end stages
are switched off. However the electronic circuitry that controls the amplifier remains in operation. In this
condition the unit consumes about
4
Watt from the main supply. This does not damage the components in
any way but is not environmentally friendly because of the unnecessary energy consumption.
CARE OF THE CASING
The surface and text of the casing are mainly scratch resistant. To clean use a mild soap solution or general
spirit based glass cleaner (use sparingiy) with a soft lint free cloth.
WARNING
Care should be taken during cleaning to ensure that no liquids can ingress into the casing. For safety reasons
it is advised to remove the power cable from the mains supply before cleaning the casing with a damp cloth.
Do not use solvents or abrasives for cleaning. This could damage the surface or text.
27