AvMap Geosat 5 APRS Руководство - Страница 8

Просмотреть онлайн или скачать pdf Руководство для GPS AvMap Geosat 5 APRS. AvMap Geosat 5 APRS 12 страниц. For: kenwood tm-d710 a/e kenwood tm-d700 a/e kenwood th-d7 a/e

Печатать страницу

if they do press the [TONE] button until none of these appear.

e. Press the menu button [MNU] and use the control knob to get to the APRS setup menu {APRS

3-X} (the X here can be any letter or number) and press the [OK] button to select/enter.

f. Use the [é] and [ê] buttons to go to different screens in the APRS menu and the [OK] button to

select/enter that particular screen.

g. Once you make your selection and/or entry push the [OK] button again to save the selection/

entry. Then go back to 'f.' above to get to the next APRS screen and enter all the Table 1 settings

below.

h. Press the [ESC] button to leave the APRS setup screen and return the D700 user screen.

i. You can now power down the radio and it will keep your settings.

AvMap Geosat 5 set-up

a. While programming the AvMap Geosat 5 and/or the Kenwood TM-D700, the communication

cable should be disconnected. Strange and/or bad things can occur if you fail to head this

warning!

b. Items in [ ] are buttons and/or knobs and { } are items you enter/see on the Geosat 5 screen.

c. Begin by pressing the [Page] button to turn the Geosat 5 on.

d. After the "Welcome on board" On the {WARNING} page press [Accept] auto selects accept after

5 seconds

e. On the {MAIN MENU} page press [SETTINGS]

f. On the {SETTNGS} page press [User Preferences]

g. On the {USER PREFERENCES} page press [Interface]

h. Press [=>] to go to 2/2 page.

i. On the {INTERFACE} page press [APRS 9600] radial button 9600 seems to work best for the

Kenwood APRS radios

j. On the {INTERFACE} page press [OK]

k. On the {USERPREFERENCES} page press [OK]

l. On the {SETTINGS} page press [MAP]

Making it all work!

a. Make sure both the Kenwood TM-D700 and AvMap Geosat 5 are turned OFF!

b. Connect the four pole 2.5mm communication cable end to the Geosat 5's TMC receptacle and

the three pole 2.5 mm end to the D700's GPS receptacle. IMPORTANT! These are easily reversed

and hooked up backwards; also when connecting to the Geosat 5 make sure you plug into the

TMC receptacle, not the ANT receptacle which is right next to it and the same size! Check for a

good click into the unit.

c. NOW POWER UP BOTH UNITS!

d. If your Kenwood D700 powers up in VFO mode (voice communications) push and hold the [F] button

for 1 second and then push the [TNC] button. This will place your D700 in {TNC APRS} mode.

e. GEOSAT 5. After the "Welcome on board" greeting use the [cursor knob] to select {YES} when

asked about the {Would you like to drive in Passenger Mode?}.

f. DOES IT WORK?? You will know you have done it right when you see {GPS} blinking at the top

of your D700 screen and {1200} just to the right of that constantly on. The blinking GPS means

that your GEOSAT 5 is 'TALKING' to your D700!

g. To begin transmitting your position push and hold the [F] button for 1 second and then push the

[Beacon] button.