Aqua Pulse Spas AIRLIE LUXURY SPA Инструкции

Просмотреть онлайн или скачать pdf Инструкции для Горячая ванна Aqua Pulse Spas AIRLIE LUXURY SPA. Aqua Pulse Spas AIRLIE LUXURY SPA 5 страниц.

AIRLIE LUXURY SPA 700 LITRES START UP INSTRUCTIONS

Note: It is extremely important that you fill your spa with water and fit the hardcover as soon as the spa is delivered

even if your electrician is not coming straight away.

Remove the filter from the spa, see page 7 in your user manual.

Place a hose in the filter box to fill the spa with water, see page 7 in your user manual.

Remove the fittings from your hose to prevent them falling into the spas plumbing.

Set your main diverter on the spa to the centre so that both sides of the spas plumbing will fill up with water.

Refer to page 9 your user manual to locate the main diverter.

Fill the spa with water until the top of the highest jets are completely under water then place your filter back in the spa.

Your hardcover must always be on the spa when not in use, and the spa must always be filled with water.

An empty or partially empty spa of water during sunlight hours can cause deforming, melting, crazing, discolouration,

blisters or holes in the spa's fiberglass, acrylic and fittings, this can happen within minutes of the spa being emptied or

partially empty. Your warranty does not cover deforming, melting, crazing, discolouration, blisters or holes in the spa's

acrylic and fittings, so it is especially important your hardcover is on the spa when not in use and the spa is always filled

with water during daylight hours.

GARDEN HOSE FITTING

Locate the small plastic bag in the spas packaging, this bag has the garden hose fitting which you will need when it

comes time to drain the spa in the future.

HARDCOVER INSTALLATION

Locate your hardcover screws & Hardcover keys, these will be with the hardcover itself.

Place your hardcover on the spa and position it to fold in the direction of your preference.

On each strap of the hardcover there is a black plastic lock. Press the two prongs on each lock together and gently pull

downwards to remove the section of the lock which you will need to screw onto the spas cabinet. With the section of the

lock you have in your hand place it behind the prongs which are attached to the hardcover strap lined up so that the

bottom of each part is flush. Now raise the section of the lock you have in your hand towards the top of the spa by 2cm

and mark the position of the two holes on each lock onto the spas cabinet. Using the smaller screws supplied in the

green bag screw each lock onto the spas cabinet. Do not pre-drill holes the screws will self-tap in, if using a drill stop

before the screw is completely tight and finish tightening the screw by hand, if you over tighten the lock you will crack

the plastic.

NEVER CONNECT POWER USING AN EXTENSION LEAD

The use of an extension lead will void your spas warranty.

Have a qualified electrician connect the spa to power.

The power supply your electrician needs to connect is a 10Amp Dedicated Single Phase connection with the appropriate

sized Residual Current Device in your houses metre box.

Please refer to page 5 through to page 6 of your user manual.

Once the spa has power connected to it and it is filled with water your electrician can turn the power on.

Never turn the spa on if you do not have it filled with water.

While your electrician is still on site, put the spa into Active mode, see page 10 in your user manual.

Once you are in active mode press Jets 1, see page 11 in your user manual.

You should now have water movement within the spa, let the spa run for 5 minutes then press Jets 1 to turn the pump

off. If you have no water movement at this stage have your electrician contact the store while they are still onsite.

Visit: www.aquapulsespas.com.au