Avtek Soundbar Руководство - Страница 12

Просмотреть онлайн или скачать pdf Руководство для Акустическая система Avtek Soundbar. Avtek Soundbar 19 страниц.

Печатать страницу

- If necessary, ask a properly skilled technician to

install the device on the wall.

1. FIG. B: Two holes need to be drilled in the wall

at the same height from the floor, 40 cm apart

from each other. You can use the drilling template

30 included with the product to mark the location

of the holes.

2. Insert the rawlplugs 29 into the holes drilled.

3. Insert the screws 28 in the rawlplugs 29 and

tighten them.

4. Insert all the necessary cable connectors into the

sockets (see "Connections" on p. 14).

NOTE: If you are installing the soundbar on a wall

and intend to use optical input OPTICAL IN (11),

use a jack that is not longer than 3 cm (or use a

TOSLINK angle adapter) to prevent the optical

cable from kinking and avoid its damage.

5. Connect the power supply unit 7 to the device.

6. Suspend the device on the wall, hooking the wall

mounting brackets on its back

28 against the screw heads.

4.3 Connections

CAUTION: Before you start making cable

connections, make sure the soundbar and the

devices to be connected to it are switched off.

Please also read the operating instructions for the

devices which you are connecting.

• A subwoofer can be connected to the RCA

(cinch) socket SUB OUT (10). It will then be

automatically controlled by the soundbar.

4.4 Turning on

NOTE: When switched off, the soundbar remains in

standby mode. As the device still uses some

electricity while in standby, if you wish to turn it off

completely you need to unplug its power supply

unit 7 from the wall socket.

• Connect the power supply unit 7 to an easily

accessible wall socket nearby.

The red LED 1 will light up on the soundbar. The

device is now in standby mode.

5. Operation

NOTES:

• All adjustments can conveniently be carried out

using the remote control. The key features can also

be operated with the buttons on the device.

However, the operation instructions provided in

this manual usually assume you are using the

remote control.

• The device switches to standby mode...

- if no Bluetooth connection is established

within 20 minutes, or

- if it does not detect any input for 20

minutes.

• Press the POWER button 27 to button to switch

on the device which is in standby mode.

5.1 Selecting connection type

1. To activate the desired input connection, press

the appropriate button: AUX (17), LINE IN (26),

OPTICAL (16) or 14 (see "Connections" on p. 14).

2. Operate the device which is the signal source to

start playback or to select and control music tracks.

NOTE: In order to use the optical input, set the

audio device output to "PCM downmix".

5.2 Sound settings

NOTES:

• Each changes to sound settings is confirmed by

the device with quick flashes of LED 1, until the

minimum/maximum value has been reached.

• Controlling the level of treble and bass can only

be done in the "Music" setting. To access it, press

the MUSIC 18 button.

Volume control

• During playback use

VOLUME –/+ buttons (19).

Mute

1. To mute the sound, press

MUTE button (15). LED 1 will start flashing.

2. To switch the sound back on, press MUTE again

or use one of the VOLUME -/+ buttons.

VOLUME –/+ buttons (19). LED 1 will light up.

Equalizer presets

• Press one of the buttons 18 to select a preset

sound profile for music (MUSIC), film (MOVIE) or

speech (DIALOG).

• Press the MUSIC button (18).

- Use the TREBLE -/+ buttons (25) to adjust the

treble level.

- Use the BASS -/+ buttons (21) to adjust the level

of bass.

5.3 Establishing a Bluetooth

connection

NOTES:

• The identification of the device is "SSB 36 A1".

• After it has been switched over to Bluetooth,

the device will automatically attempt to establish a

connection with the last paired device.

• Please note that the connection process may

vary slightly depending on the device and the

software used.

1. Press button 14 to switch on the Bluetooth

connection. LED 1 will start flashing blue.

2. Switch on the audio device (e.g. your

smartphone) and initiate the search for new

Bluetooth connections on it.

3. Press the PAIR button (5) on the soundbar and

hold it depressed for approximately 1 second. The

blue LED 1 will flash rapidly. The audio source

device should now identify the soundbar as "SSB

36 A1".