Dell Networking N2048P Обновление микропрограммы - Страница 10

Просмотреть онлайн или скачать pdf Обновление микропрограммы для Переключатель Dell Networking N2048P. Dell Networking N2048P 21 страница.
Также для Dell Networking N2048P: Руководство по установке (49 страниц)

Dell Networking N2048P Обновление микропрограммы
Upgrade Procedure Dell™ Networking
N2024/N2024P/N2048/N2048P/N3024/N3024F/N3024P/N3048/N3048P
Switches
C07.4.5
C07.4.6
C07.5
C08. DDR40_PHY_DDR3_MISC : Start DDR40_PHY_RDLY_ODT....
C09. Start ddr40_phy_autoidle_on (MEM_SYS_PARAM_PHY_AUTO_IDLE) ....
C10. Wait for Phy Ready
Programming controller register
ddr_init2: Calling soc_ddr40_shmoo_ctl
Validate Shmoo parameters stored in flash ..... OK
Press Ctrl-C to run Shmoo ..... skipped
Restoring Shmoo parameters from flash ..... done
Running simple memory test ..... OK
DDR Tune Completed
Micron MT29F2G08ABAEA, 128 KiB blocks, 2 KiB pages, 16B OOB, 8-bit
NAND:
chipsize 256 MiB
U-Boot 2012.10-00075-g9766807 (Oct 10 2013 - 13:38:25)
DRAM:
1 GiB
WARNING: Caches not enabled
NAND:
Micron MT29F2G08ABAEA, 128 KiB blocks, 2 KiB pages, 16B OOB, 8-bit
NAND:
chipsize 256 MiB
In:
serial
Out:
serial
Err:
serial
arm_clk=1000MHz, axi_clk=499MHz, apb_clk=124MHz, arm_periph_clk=500MHz
Net:
Registering eth
Broadcom BCM IPROC Ethernet driver 0.1
Using GMAC0 (0x18022000)
et0: ethHw_chipAttach: Chip ID: 0xdc14; phyaddr: 0x1
serdes_reset_core pbyaddr(0x1) id2(0xf)
bcmiproc_eth-0
boot in 3 s
Creating 1 MTD partitions on "nand0":
0x000000200000-0x00000f000000 : "mtd=4"
Loading file '/image1' to addr 0x70000000 with size 18336782 (0x0117cc0e)...
Done
## Booting kernel from Legacy Image at 70000074 ...
Image Name:
Image Type:
Data Size:
Load Address: 61008000
Entry Point:
Contents:
Image 0: 2438620 Bytes = 2.3 MiB
Image 1: 790997 Bytes = 772.5 KiB
Image 2: 474 Bytes = 474 Bytes
Image 3: 15106486 Bytes = 14.4 MiB
Verifying Checksum ... OK
## Loading init Ramdisk from multi component Legacy Image at 70000074 ...
Uncompressing Multi-File Image ... OK
boot_prep_linux commandline: console=ttyS0,9600 maxcpus=2 mem=1024M root=/dev/ram
mtdparts=nand_iproc.0:1024k(nboot),512k(nenv),256k(vpd),256k(shmoo),243712k(fs),16384k(dia
gs) ubi.mtd=fs ethaddr=f8:b1:56:1a:60:e4 quiet
Starting kernel ...
starting pid 369, tty '': '/etc/init.d/rcS'
starting pid 483, tty '/dev/ttyS0': '/etc/rc.d/rc.fastpath'
Mounting /dev/mtdblock4 at /mnt/fastpath...done.
Mounting tmpfs at /mnt/application...done.
Checking for USB Device... done.
No USB Device found!
Boot Menu Rev: 6.0
System for iproc_pct
ARM Linux Multi-File Image (gzip compressed)
18336602 Bytes = 17.5 MiB
61008000
Page 7