Dell S6000-ON Руководство по устранению неполадок - Страница 9
Просмотреть онлайн или скачать pdf Руководство по устранению неполадок для Переключатель Dell S6000-ON. Dell S6000-ON 29 страниц. Open networking
Также для Dell S6000-ON: Руководство по началу работы (26 страниц), Руководство по установке (41 страниц)
Печатать страницу
ONIE Rescue bypasses the installed operating system and boots the system into ONIE until you reboot the system.
2
Press ENTER to activate the console.
Example of the Optional ONIE-uninstaller Command
After ONIE Rescue completes, the system resets and boots to the ONIE console.
NOTE:
Only use the optional onie-uninstaller command if you want to remove all the network operating software on your
system except for ONIE. This command removes any installed network operating system.
ONIE:/ # onie-uninstaller
Erasing unused NOR flash region
Erasing 128 Kibyte @ 20000 - 100% complete.
Erasing internal mass storage device: /dev/mmcblk0 (7832MB)
Percent complete: 100%
S4810–ON or S6000–ON diagnostic package
To download the diagnostic package on an S4810–ON or S6000–ON platform, follow these steps.
NOTE:
Before you begin, go to http://www.dell.com/support and download the diagnostic package. You will need your Dell EMC
support access account to download the package.
NOTE:
These steps only apply to the S4810–ON and S6000–ON platforms.
1
Enter the onie-discovery-stop command to stop the ONIE discovery mode.
2
Assign an ip address to the management interface and verify the network connectivity.
ONIE:/ # ifconfig eth0 xx.xx.xx.xx/x
ONIE:/ #
ONIE:/ #
ONIE:/ # ifconfig eth0
eth0
Link encap:Ethernet
inet addr:xx.xx.xx.xx
inet6 addr: fe80::92b1:1cff:fef4:9c76/64 Scope:Link
UP BROADCAST RUNNING MULTICAST
RX packets:18 errors:0 dropped:0 overruns:0 frame:0
TX packets:24 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1152 (1.1 KiB)
Interrupt:21 Memory:ff300000-ff320000
ONIE:/ # ping xx.xx.xx.xx
PING xx.xx.xx.xx (xx.xx.xx.xx): 56 data bytes
64 bytes from xx.xx.xx.xx: seq=0 ttl=62 time=1.357 ms
64 bytes from xx.xx.xx.xx: seq=1 ttl=62 time=0.577 ms
^C
3
Upgrade the DIAG Installer. Again, boot to ONIE Rescue mode and install onie diag installer
NOTE:
The command onie-nos-install, shown in bold, is not available in S4810-ON ONIE version 1.0.0.1; instead use
the install_url ONIE:/bin # install_url command.
ONIE:/ # onie-nos-install tftp://xx.xx.xx.xx/ON-DIAG/S4810/JUL-08-2014/diag-installer-
powerpc-dell_s4810_on_p2020-r0.bin
Stopping: discover... done.
Info: Fetching tftp://xx.xx.xx.xx/ON-DIAG/S4810/JUL-08-2014/diag-installer-powerpc-
dell_s4810_on_p2020-r0.bin ...
ON-DIAG/S4810/JUL-08 100% |*******************************| 1361k 0:00:00 ETA
ONIE: Executing installer: tftp://xx.xx.xx.xx/ON-DIAG/S4810/JUL-08-2014/diag-installer-
powerpc-dell_s4810_on_p2020-r0.bin
Verifying image checksum ... OK.
Preparing image archive ...
Preparing image archive ...sed -e '1,/^exit_marker$/d' /installer | tar xf - OK.
Diag Installer: platform: powerpc-dell_s4810_on_p2020-r0
HWaddr 90:B1:1C:F4:9C:76
Bcast:xx.xx.xx.xx
MTU:1500
TX bytes:6864 (6.7 KiB)
Mask:xx.x.x.x
Metric:1
ONIE diagnostics
9