AVYCON AVR-HN808P8-FDT Краткое руководство по эксплуатации

Просмотреть онлайн или скачать pdf Краткое руководство по эксплуатации для DVR AVYCON AVR-HN808P8-FDT. AVYCON AVR-HN808P8-FDT 2 страницы. Avr-hn808p8-fdt

Печатать страницу

FACIAL DETECTION NVR

QUICK START GUIDE

Thank you for purchasing our product. There may be some outdated information or minor

printing errors in this manual. Updates are continually being added into the newest version of

this manual. We will readily update the products or procedures described in the manual. The

contents are subject to change without notice.

1. WARNING AND CAUTION

•

If the product does not work properly, please contact your dealer or the

nearest service center. Never attempt to disassemble the terminal yourself.

(We shall not be responsible for any problems caused by unauthorized

repair or maintenance.)

•

Keep product away from liquid while in use.

•

In the use of the product, you must be in strict compliance with the

electrical code of your country or state.

•

Do not use terminal beyond speciﬁed voltage range.

•

Do not drop the terminal or subject it to physical shock.

•

If cleaning is necessary, please use a clean cloth to wipe it gently.

•

Do not place the terminal directly in the sun or a very bright light source.

Do not place the terminal in extremely hot, cold (operating temperature

should be -30°C~60°C), dusty, or damp locations, and do not expose it to

high electromagnetic radiation.

•

To avoid overheating, decent ventilation for the product is required in the

operating environment.

•

Some parts connected to device may need to be replaced regularly due to

environmental conditions or the lifespan of these parts. Regular

maintenance checks are recommended for all users.

2. PACKING CHECK

Please check the device and the accessories after receiving the device. If

there is any damage, shortages or defects, please contact your dealer

immediately.

3. HDD INSTALLATION

This series of products supports 1 x SATA hard drive. Plese make sure the

device is powered off before the installation. The pictures of the installa-

tion are only for reference.

① Loosen the screws to open the cover.

②

Screw the screws into the HDD, but don't tighten them.

③

Place the HDD onto the bottom of the machine.

④

Turn over the machine and sequre the HDD with the screws.

⑤

Connect the power and data cables.

⑥ Install the cover back on and secure it with screws.

TIP: Please check the inside structure of the device and make sure the

cables are connected well before installing the back cover.

4. REAR PANEL INSTRUCTION

The interface of the panel is for reference only.

Name

Description

DC48V

Connector for power input

POE PORTS

8 PoE network ports; connect to PoE IP cameras / panels

LAN

Ethernet port

Connectors for USB devices (like USB mouse, USB storage

USB

device for backup or upgrade, etc. )

VGA

Connect to monitor

HDMI

Connect to high deﬁnition display device

AUDIO OUT

Audio output

AUDIO IN

Audio input

P / Z

Connector for a PTZ device. Y is TX+, Z is TX-

K /B

Connector for a keyboard. A is TX+, B is TX-

GND & ALARM IN

Connectors for alarm input devices, like sensors

ALARM OUT

Relay output; connectors for external alarm output devices

5. STARTUP & SHUTDOWN

› Startup

① Connect the monitor and the power.

②

The device will boot and the power indicator will display blue.

③

A wizard window will pop up.

› Shutdown

Click "Start" and select "Shutdown" icon. This will bring up a shutdown

window. The device will shut down by clicking "OK" button. Then

disconnect the power.

6. LOGIN

You must conﬁgure the wizard if you start the NVR for the ﬁrst time.

Choose the language and read the privacy statement. Then set the data,

time and zone as needed. After that, set the login password.

Wizard

Admin Password Setup

Username

admin

New Password

123456

Confirm Password

123456

Display Password

Pattern Lock

Enable

Edit

The default username is admin and the default password of admin is

123456. Set your own password or use the default one when you use the

wizard for the ﬁrst time. Enable pattern lock and click "Edit" to set the

pattern lock. Then set security questions and answers. It is important for

you to remember these answers, or you will not be able to reset your

password. Click "Next" to continue.

7. DISK SETTINGS

You must conﬁgure the wizard if you start the NVR for the ﬁrst time.

Choose the language and read the privacy statement. Then set the data,

time and zone as needed. After that, set the login password.

8. NETWORK CONFIGURATION &

ADD DEVICES

① Enter IP address, subnet mask, gateway, etc. If using DHCP, please enable

DNCHP in both the NVR and the router.

②

Enter HTTP port (the default value is 80) and server port (the default port

is 6036).

③

The internal ethernet port is the port which connects all the PoE ports

with the NVR system. The PoE ports are available if the internal ethernet

port is online; if is ofﬂine, all the PoE ports will be unavailable.

Wizard

Network Settings

Internal Ethernet Port ( Online )

Ethernet Port 1 ( Online )

Obtain an IP address automatically

Address

192 . 168 .

1 .

10 . 151 .

Subnet Mask

255

Subnet Mask

Gateway

192 . 168 .

1 .

Obtain DNS automatically

Preferred DNS

Alternate DNS

RTSP Port

554

HTTP Port

HTTPS Port

443

Sever Port

6036

④ Add camera. Click "Next" to go to the following interface.

Wizard

Network Settings

Add Camera

No.

Address

Edit

Port

Protocol

Model

Version

192.168.1.20

XXX

5.0.2.0

192.168.1.38

XXX

5.0.1.0

192.168.2.45

XXX

5.0.2.0

Remain Bandwidth: 77 / 80 Mb

Refresh

Add All

Delete All

No.

IP Camera Name

Address

Protocol

Status

Edit

[POE1] IPC

Facial Panel

Online

10.151.151.103

151 .

255

Cancel

Add

_ _ _

Delete