AVYCON AVR-HT504A-1T Краткое руководство по эксплуатации

Просмотреть онлайн или скачать pdf Краткое руководство по эксплуатации для DVR AVYCON AVR-HT504A-1T. AVYCON AVR-HT504A-1T 2 страницы. All-in-one dvr

Печатать страницу

All-in-One DVR

Quick Start Guide

Note: Please read this instruction carefully for correct use of the product and preserve it for reference purposes.

All the examples and pictures used here are for reference only. There may be several technically incorrect places

or printing errors in this manual. The updates will be added into the new version of this manual. The contents of

this manual are subject to change without notice.This device should be operated only from the type of power

source indicatedon the marking label. The voltage of the power must be veriﬁed before using the same.

1. HDD Installation

This series of the product supports 1 SATA hard drive. Please make sure

that the device is powered off before the installation. The pictures of

the installation are only for reference, please take the real object as the

standard.

2. Screw the screws into the HDD

1. Loosen the screws to open the

but not tighten them.

cover.

4. Connect the power and data

3. Place the HDD onto the bottom

cables.

of the machine.

5. Turn over the machine and secure

6. Install back the cover and secure

the HDD with the screws.

it with the screws.

2. Rear Panel Installation

CVBS

ALARM OUT ALARM IN

COM1

NO1

GND

COM2

NO2

GND

AUDIO IN

VIDEO IN

AUDIO OUT

Rear Panel for 8CH

Name

Description

ALARM OUT

Relay output; connect to external alarm

Alarm input for connecting sensor

ALARM IN

GND

Ground

Audio input

AUDIO IN

VIDEO IN

Video input

CVBS

CVBS output

Audio output

AUDIO OUT

Connect to high definition display device

HDMI

VGA

Connect to monitor

Ethernet connector

LAN

Connector for USB devices

USB

The interfaces of the rear panels are for reference only.

Connector for e-SATA

e-SATA

Connect

for

. A is TX+,B is TX-

RS485

RS485 devices

Power input

DC12V

3. Startup & Shutdown

• Startup

1. Connect the monitor and the power.

2. The device will boot and the power indicator will display blue.

3. A wizard window will pop up.

• Shutdown

Go to "Main Menu" and then select "Shutdown" icon. This will bring up

a shutdown window. The device will shut down by clicking "OK" button.

Then disconnect the power.

4. Login

For our HT500A series DVRs, the default username is admin and the

default password is 123456. When starting HT500A series DVR for

the ﬁrst time, you will see a prompt to begin a startup wizard. You can

skip this wizard if you would like, but it will help you conﬁgure basic

settings for your DVR. The wizard may allow you to also change the

default password for better security. If you decide to skip the wizard,

to access the live view and start using your DVR click on the Start

button in the bottom left of the menu bar on the bottom of the

screen and then click on Login and enter in the default password.

Username

adm in

Enter Password

Password

Display Password

Edit Security Question

5. Analog Camera Connection

First connect the camera to the DVR. Then go to Start → Settings

e SATA

→ Camera → Manage Camera → Signal Access Set to checkmark

the video mode. The actual signals input shall correspond to the

video mode. Please refer to User Manual for details.

VGA

LAN

USB

RS485

DC12V

Network Configuration & Add IP Camera

Internet

After you ﬁnish adding IP cameras, you can see the live images

through the monitor of the DVR. The following will mainly

introduce how to add the IP cameras via LAN/WAN.

• LAN

1. Set the network of the DVR. Go to Start → Settings → Network

→ TCP/IPv4. Input IP address, subnet mask, gateway, etc. If using

DHCP, please enable DHCP in both the DVR and the router.

2. Go to Start → Settings → Network → Port. Input HTTP port

(the default value is 80), server port (the default port is 6036).

3. Click "Apply" to save the settings.

TCP/IPv4

IP Address Settings

Ethernet Port 1 ( Online )

Obtain an IP address automatically

IP Address

Subnet Mask

Gateway

Obatin DNS server address automatically

Preferred DNS

Alternate DNS

Quickly Add

No.

IP Address

192.168.2.45

Selected: 1/1

Remain Bandwidth: 10 / 10 Mb

Cancel

Port

DDNS

E-mail

UPnP

NAT

Network Status

192 . 168 .

1 .

0 .

192 . 168 .

1 .

192 . 168 .

1 .

0 .

Add Camera

Manually Add

Protocol

Model

Version

Port

Edit

Subnet Mask

255.255.255.0

XXX

4.0.0.1.beta1

Default Password

Add

Edit IP

Mac Address

CE :98 :23 :75 :35 :22

IP Address

192 .168 . 1 . 45

Subnet Mask

255 . 255 . 255 . 0

Gateway

192 .168 . 1 . 1

Usernam e

admin

Password

Cancel