HP -380467-003 - COMPAQ PRESARIO C300 C500 C700 F500 F700 LAPTOP CHARGER Руководство - Страница 6

Просмотреть онлайн или скачать pdf Руководство для Настольный компьютер HP -380467-003 - COMPAQ PRESARIO C300 C500 C700 F500 F700 LAPTOP CHARGER. HP -380467-003 - COMPAQ PRESARIO C300 C500 C700 F500 F700 LAPTOP CHARGER 24 страницы. Intervideo ã¥â®â¶ã¥âºâ­ã¥â½â±ã©â„¢â¢ ã¥â¿â«ã©â‚¬å¸ã¥â€¦â¥ã©â€”â¨ã¦å’‡ã¥ââ€”
Также для HP -380467-003 - COMPAQ PRESARIO C300 C500 C700 F500 F700 LAPTOP CHARGER: Руководство пользователя (37 страниц), Руководство по поддержке (27 страниц), Руководство (10 страниц), Краткое руководство по эксплуатации (8 страниц), Руководство по началу работы (2 страниц), Важная информация (1 страниц), Важная информация (1 страниц), Важное уведомление (1 страниц), Дополнительное руководство (1 страниц), Руководство по поддержке (29 страниц), Руководство (8 страниц)

Печатать страницу
HP -380467-003 - COMPAQ PRESARIO C300 C500 C700 F500 F700 LAPTOP CHARGER Руководство
3 Disconnect the modem/telephone cable, if present.
WARNING: To reduce the risk of personal
injury from electrical shock or hot
surfaces, disconnect the power cord from
the wall outlet, and allow the internal
system components to cool before
touching.
4 Disconnect the power cord from the electrical outlet
and then from the PC.
5 Disconnect all other attached cables (such as the
keyboard, mouse, and monitor) and all external
devices.
CAUTION: Static electricity can damage the
electronic components of the PC or
optional equipment. Ensure that you are
discharged of static electricity by briefly
touching a grounded metal object.

After Closing the PC

To avoid injury and equipment damage, always
follow this procedure in this order after closing the PC:
1 Reconnect the power cord.
WARNING: To reduce the risk of electrical
shock, fire, or damage to the equipment,
do not plug telecommunications or
telephone connectors into the network
interface card (NIC) (labeled as an
Ethernet connector).
2 Reconnect the modem/telephone cable and all
other attached cables (such as the keyboard,
mouse, and monitor) and external devices.
3 Turn on the PC and all peripherals.
4 If you installed an add-in card, install any software
drivers supplied by the card manufacturer.
2
Upgrading and Servicing Guide

Removing the Side Panel

1 See "Before Opening the
PC" on page 1.
2 Loosen the two
thumbscrews on the right
side of the back panel.
The first time you loosen
these screws, you may
need to use a Phillips
screwdriver.
WARNING:
Beware of sharp
edges inside the
chassis.
3 Slide the panel back about 2.5 cm (1 inch), lift it
off the unit, and set it aside.
You do not need to remove the other side
NOTE:
panel to replace the hardware listed in this guide.

Replacing the Side Panel

1 Align the notches inside
the side panel with the
holes on the chassis
frame.
2 Slide the side panel
forward on the frame until
it locks into place, and
then tighten the
thumbscrews on the side
panel.
3 See "After Closing the PC"
on page 2.