Allnet ALL168211 Руководство по простому запуску - Страница 2

Просмотреть онлайн или скачать pdf Руководство по простому запуску для Беспроводная точка доступа Allnet ALL168211. Allnet ALL168211 2 страницы. Wireless n extender

Печатать страницу

Easy Start Guide

ALLNET HomePlug devices are configured with a common Private Network Name, adding new HomePlug

devices to an existing network with the default factory configuration is as easy as plugging the device to thepower

outlet. The Simple Connect button makes it easy to activate both the security for the network and create multiple networks on the same

power line.

ALL168211 Device Overview

Power LED

OFF

- No Power.

- After Simple Connect is pressed for two seconds, this LED

will blink to confirm the button is pressed.

- When Simple Connect is pressed for at least 10 seconds,

this LED will blink to confirm the Private Network Name

is reset.

On Power Saving Mode

- Slowly blinking green.

Powerline LED

OFF

- Device is not connected to a HomePlug AV network.

- This LED remains on when the device is part of a

HomePlug AV network.

- The LED colors represents the connection rate within the

HomePlug AV network whether it is bad (red), good

(amber), or excellent (green).

- The LED flashes to indicate network activity.

Ethernet LED

OFF

- An Ethernet device is not connected.

- An Ethernet device is connected.

- The LED flashes to indicate Ethernet activity.

Wireless LED/Button

LED OFF

- Wireless is disabled.

LED ON

- Wireless is Enabled.

- The LED flashes to indicate wireless activity.

The LED is also a button, which can enable or disable wireless function.

Ethernet Ports

This is where you connect your Ethernet devices. (10/100 Mbit)

Connect-Button

- Press for 2 seconds to initiate pairing.

- Press for 10 seconds to randomize the private network name.

Reset-Button

Press for 3 seconds to restore factory defaults.

How to add a new ALL168211 to an existing security-

enabled Powerline-Network?

Schritt 1

Existing Network

Additional

ALL168211

Plug the additional ALL168211 to a power outlet near

your existing HomePlug network so that you can

observe the LED behavior on the individual ALL168211.

Schritt 3

The POWER

LED will start

Blinking

to blink.

POWER LED

NOTE: If the

POWER LED

did not blink,

repeat the

step until you

got the

POWER LED

blinking

from the

existing network

Press the Simple

Connect button for 2

secs on the additional

ALL168211

Make sure you do this action within 2 mins after

pressing the Simple Connect button on the first

Powerline. The LEDs on both devices will switch OFF

and ON twice to signify they are searching for the

other device to pair with.

The ALL168211 is compatible with other HomePlugAV 200Mbps.

ALL168211 Wireless N Extender

Schritt 2

Upon release, the

POWER LED will blink

continuously for 2

mins.

Press the Simple

NOTE: If nothing

Connect button für 2

happened on the

secs on either

POWER LED, try

Powerline Device.

further by pressing the

same button for 2 secs.

Existing

Powerline-Network

Pressing the Simple Connect button for 2 secs, this will

trigger the unit to search for another Simple Connect

enabled Powerline Device, a time window of 2 mins is

programmed on the device.

Schritt 4

Neues Powerline-Netzwerk

All Powerline LED will be ON upon getting the

additional ALL168211 join the existing network.

NOTE: IF the Powerline LED on ALL168211 is not ON,

repeat steps 1-4.

Setup Diagram

Broadband

Internet

Modem/Router

Room 1

1. Once you have completed the pairing, connect a Powerline Device to a wall

socket in Room 1.

2. Plug one end of the ethernet cable to your Modem/Router and then connect

the other end to the Powerline ethernet port.

3. In Room 2, connect the ALL168211 to a wall socket and check the Powerline

LED behavior. This LED should be ON to ensure that the device is paired with

the Powerline in Room 1.

4. Plug one end of the ethernet cable to your Ethernet device and then plug

the other end to any of the available ethernet port of your ALL168211.

Configure ALL168211 as WLAN Access Point

By default your wireless connection is 'Enabled'. Using your ALL168211 Utility allows

you to configure your wireless settings. Install the CD utility that comes with the

package and then follow the steps below.

1. Plug one end of the ethernet cable to your Computer and then connect the

other end to the ALL168211 ethernet port.

2. Open your ALL168211 Utility and select the Wireless Tab.

3. Select Wireless Settings, this page allows you to change your Wireless Settings.

4. Select Enable to enable your wireless connection.

5. By default your SSID is „ALL168211". You may change this SSID to your desired

SSID on the SSID Box.

6. For Broadcast SSID select Enable to broadcast your device wireless

network name.

7. It is recommended to set your Wireless Security to avoid unauthorized

connection to your network. Set your desired Wireless Security then click

Save to save your settings. We recommend to use WPA2 as Security Type.

Powerline

Wireless Smartphone

Notebook

Computer

Room 2