Dialogic DM3 Media Boards DM/V2400A-PCI Карта быстрой установки

Просмотреть онлайн или скачать pdf Карта быстрой установки для Сетевая карта Dialogic DM3 Media Boards DM/V2400A-PCI. Dialogic DM3 Media Boards DM/V2400A-PCI 2 страницы. Dm3 media boards quick install card for pci

Печатать страницу

Dialogic

DM3 Media Boards

Quick Install Card for PCI

DM/V2400A-PCI

Part Number 64-0017-02

Dialogic Corporation.

Before You Begin

Protecting the Board from Damage

CAUTION:

All computer boards are sensitive to

electrostatic discharge ("ESD"). Handle all static-sensitive

boards and components at a static-safe work area,

and observe anti-static precautions at all times.

If you are not familiar with ESD safety precautions, visit

http://www.dialogic.com/support/hwinstall

to learn more.

Unpacking the Board

Unpack the Dialogic

DM3 Media Board ("board")

according to the following steps:

Prepare a static-safeguarded work area.

Carefully remove the board from the shipping

carton and anti-static packaging. Handle the

board by the edges and avoid touching the

board's components.

Lay the board on the static-dissipative work

surface.

NOTE: Place boards in static-shielding bags when

carrying boards from station to station.

CAUTION: Do not remove the board from the anti-static

packaging until you are ready to install it. Observe proper

anti-static precautions at all times.

Configuring the Hardware

Board Identification

The Dialogic

DM3 device driver, part of the Dialogic

System Software, assigns board instance numbers in

ascending order (beginning with 0) as it detects each board

in your system. A board instance number is the

CH4 CH3 CH2 CH1

Red

Yellow

Green

Loopback

identification (ID) number used by the system software to

recognize the board.

NOTE: If you add a board to the system, the existing

board instance (ID) numbers may change, depending upon

the PCI bus and slot number where the new board is

installed.

Windows System

After the Dialogic

hardware and the Dialogic

Software are installed, refer to the Dialogic

Manager (DCM) utility to retrieve the board instance (ID)

number(s) assigned to the board(s) in your system.

See the DCM online help for more details about board

identification.

Linux System

In a Linux system, you must set SW1 to a unique number

for each installed board in your system. Use a non-

magnetic screwdriver to turn SW1 to 1 of 16 board

settings, 0-9 or A-F.

Physical Description

JP2A

JP2B

After the Dialogic hardware and Dialogic System Software

are installed, refer to the proper configuration files to

retrieve the assigned board instance (ID) number(s)

assigned to the board(s) in your system. For more

information about Linux configuration files, see the

Dialogic® Software Installation Reference.

Installing the Hardware

System

Configuration

NOTE: Dialogic recommends that you install Dialogic

hardware before Dialogic

adding hardware to an existing system, you do not need to

uninstall existing Dialogic software.

1. With your computer on the static-safe work area,

switch off the power and disconnect all power cords

from the electrical outlets.

2. Remove the chassis cover plate.

3. Select an empty PCI expansion bus slot and remove

the slot's retaining screw and access cover plate (if

applicable).

4. If you are not installing your board in an ISA form

factor PCI slot, remove the ISA edge retainer from

General Network Interface Alarm

the board.

LED (not applicable)

Power LED

5. Using the slot's board guides, insert the board edge

connector into the bus slot. Press firmly until the

Reset LED

board is securely seated in the slot.

SW1: Rotary switch to set board

identification (UNIX systems only).

Installing a PCI Board

POST LEDs: Indicate Power On Self

Test (POST) status during power up.

Alarm Status LEDs:

Red-Not functional in this

assembly.

Computer

Yellow- Not functional in this

Chassis

assembly.

Carrier Signal- Not functional

in this assembly.

Loopback- Not functional in

this assembly

CT/MVIP Bus Termination

Jumpers: Bus signal is terminated

when the corresponding jumper is

installed. Signal must be terminated

only on boards at each end of the

CT Bus cable.

6. Replace and tighten the slot's retaining screw to

JP2A: CT Bus termination jumper

secure the board firmly in the chassis (if applicable).

JP2B: MVIP Bus termination jumper

7. Select a new PCI slot and repeat steps 3-6 for each

P3: CT Bus connector

board you are installing.

ISA Edge Retainer

8. Use the CT Bus cable to connect the board(s) you are

Signal Processing Daughterboard

installing to other boards in the system.

NOTE: Your system may include both CT Bus and

SCbus boards. To connect both board types, you must

install a CT Bus/SCbus Adapter on one of the CT Bus

boards in a system. See the CT Bus/SCbus Adapter

Quick Install Card for installation details about the

Adapter and the bus cables. Contact your Dialogic

Sales Representative to order an Adapter.

9. Install CT Bus Termination Jumpers only on boards

located at each end of the CT Bus cable. See Physical

Description section.

10. Replace the chassis cover when finished and reconnect

software. However, if you are

the power cords.

11. Turn the power to the chassis ON.

CAUTION: If your BIOS is set to use Plug and Play

technology and there are ISA boards in your system,

an IRQ conflict can be created if the DM3 board is

assigned the same IRQ as an ISA board. This could

cause the machine to stop responding. You can prevent

this by entering the BIOS and reserving the appropriate

IRQs (those used by your ISA boards) for ISA use

only.

Remove

PCI

Cover

Board

Plate

32-Bit

PCI Slot

16-Bit

ISA Slot