Dialogic D4PCIU Быстрая установка

Просмотреть онлайн или скачать pdf Быстрая установка для Компьютерное оборудование Dialogic D4PCIU. Dialogic D4PCIU 2 страницы. Quick install card for pci universal
Также для Dialogic D4PCIU: Быстрая установка (2 страниц)

Печатать страницу

Intel

Dialogic

D/4PCIU, D/4PCIUF

Quick Install Card for PCI Universal

Part Number C60983-001

Intel Corporation.

Before You Begin

Electrostatic Discharge

CAUTION

All computer boards are electrostatic sensitive. Handle

all static sensitive components, boards and computers at

a static-safeguarded work area.

A static-safe work area consists of:

• A grounded, static-dissipating wrist strap that drains

static charge from the person wearing the strap.

•

A work surface covered with or composed of a

grounded, static-dissipating material that drains electrical

charges from conductive materials placed on the surface.

Both items ensure that static charges are drained to a safe rate

and current level.

Always observe these practices to maintain a static-safe

environment during the entire installation:

•

Use the wrist strap to ground yourself to the static-safe work

area.

•

Remove the board from the shipping carton and static

shielding at the static-safe work area.

•

Lay the board on the static-dissipating work surface.

A Static Safe Work Area

Static-Dissipative

Mat

Static-Dissipative

Wrist Strap

Common

Ground

Point

{

Configuring the Hardware

The position of slide switch SW4 determines how the board

responds to an incoming call when the chassis power is on but

the board is not initialized. Refer to the Physical Description

section. Set the SW4 slide switch as follows:

•

SW4 = On-hook (default): Callers hear ringing.

•

SW4 = Off-hook: Callers hear a busy signal.

NOTE: If the chassis power is off, callers hear ringing

(on-hook).

The D/4PCIU board uses Plug and Play technology, including

hardware auto-configuration for IRQ and memory address.

This technology enables quick installation and operation

using the factory default hardware settings.

The system software assigns board instance numbers in

ascending order (beginning with 0) as it detects each board in

your system. A board instance number is the identification

(ID) number used by the system software to recognize the

board. Each Board ID is based on the SW30 rotary switch

setting. See the Physical Description section.

NOTE: The ascending Board IDs automatically assigned by

the system may not correspond to a physical order in the

chassis.

Physical Description

Initial Hook State

Board Identification

1. J1-J4—RJ-11 jacks (4) connect to PBX or public

telephone network (Central Office) lines

2. SW30—Rotary switch used to manually set board

identification

3. SW4—Slide switch used to set hook state at

start-up

4. P1—Universal PCI Edge Connector

Geographical Sequence

Leave SW30 set to Board ID 0 (default) to let the system

automatically assign board instance numbers by PCI bus

logical slot number. This method is not available for ISA bus

boards.

NOTE: If you add or remove a board, the system may

change the existing board instance (ID) numbers.

Programmable Sequence

You must set SW30 to a unique number for each installed

board. Use a non-metallic screwdriver to turn SW30 to 1 of

16 board settings, 0–9 or A–F. You should assign sequential

numbers to each Intel

Dialogic

board, starting at 1. This

method is also used for all ISA bus boards.

Precedence in Mixed Systems

In systems where both ISA and PCI boards exist, PCI boards

take precedence and are numbered before ISA boards. Also,

when using both geographical and programmable assignment

methods, PCI boards that use SW30 setting 0 are numbered

before PCI boards that use SW30 settings 1–9 or A–F.

NOTES: After the hardware and the system software are

installed in a Windows system, refer to the Intel® Dialogic®

Configuration Manager (DCM) utility to retrieve the assigned

board instance (ID) number(s). After the hardware and the

system software are installed in a Linux system, refer to the

proper configuration files to retrieve the assigned board

instance (ID) number(s).