Dialogic SI/240 Руководство по быстрой установке - Страница 2

Просмотреть онлайн или скачать pdf Руководство по быстрой установке для Компьютерное оборудование Dialogic SI/240. Dialogic SI/240 2 страницы. Dialogic station interface box quick installation guide

Печатать страницу

Dialogic® Station Interface Box

Screws (4 Req'd)

SI\240 Board

(Installed)

Power Supply

Connector

STA

Connector

Rear Mounting

Screws (2 Req'd)

4. Install the Board

1. Working at a static-safeguarded work area, disconnect

the SIB's power cord from the electrical outlet and

remove the SIB cover.

Note:

To remove the SIB cover, you must first

remove the top three screws on the front panel.

Top Mounting

SI\240

Connector

Daughter

Board

Remove

CoverPlate

Board

Mounting

Posts

Diag

Port

8-Pin

Modular Jacks

Base

Board

2. Remove the desired

STA XX-XXX

cover plate and save the two rear mounting screws.

3. Attach the SI/240 board ribbon cable to the

appropriate base board connector (

Note:

When you fully seat the SI/240 ribbon

cable connector, the base board ribbon cable extractor

clips lock into the vertical position.

4. Guide the SI/240 board's STA connector into the hole

on the SIB rear panel, carefully lining up the top

mounting holes with the base board mounting posts.

5. Secure the board with four top mounting screws

(supplied) and the two saved rear mounting screws.

Note:

Make sure that the SI/240 board STA

connector contacts the SIB rear panel. Start the four

top mounting screws by hand first; then install and

fully tighten the two rear mounting screws. Finally,

fully tighten the top mounting screws.

6. After installing and connecting the SI/240 board(s),

replace the SIB cover and connect the power cord.

5. Warranty and Return Information

Warranty Period

For specific warranty information for this board, refer to the

Warranty section of the Products page, located at this URL:

http://www.dialogic.com/warranties/.

Contacting Technical Support

Base Board

Dialogic provides technical support for its products through

Connector

a network of value added distributors who are trained to

answer technical questions on installing and configuring

Dialogic

products. If you are unsure how to contact your

support channel, please call Dialogic in the United States at

973-967-6600 (9am-5pm EST) and we will assist in

obtaining the appropriate support channel.

Connector

Outside the United States please refer to

http://www.dialogic.com/support/contact to obtain

local contact information.

Dialogic also provides direct support via Dialogic

Services agreements. For more details of direct support

from Dialogic please refer to:

http://www.dialogic.com/support/DialogicPro.

Returning a Product

To return a board for warranty repair or any other returns,

please refer to the following:

http://www.dialogic.com/support/hwfaults.

To return a board for warranty repair, please refer to the

following: http://www.dialogic.com/support/hwfaults. For

connector access

all other returns, contact your vendor or Dialogic Customer

Support (for more information, see

http://www.dialogic.com/support/contact/ ).

, or

6. Sales Assistance

If you have a sales question, please contact your

local Sales Representative or the Regional Sales Office

for your area. Address, telephone and fax numbers, are

available at the Dialogic website located at:

http://www.dialogic.com/contact.htm.

To purchase Dialogic

products, please refer to the

following website to locate the appropriate supplier.

http://www.dialogic.com/purchase.htm.

All contents of this document are furnished for informational use only and are

subject to change without notice and do not represent a commitment on the

part of Dialogic Corporation or its subsidiaries ("Dialogic"). Reasonable

effort is made to ensure the accuracy of the information contained in the

document. However, Dialogic does not warrant the accuracy of this

information and cannot accept responsibility for errors, inaccuracies or

omissions that may be contained in this document.

INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION

WITH DIALOGIC

PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED,

BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY

RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED

IN A SIGNED AGREEMENT BETWEEN YOU AND DIALOGIC,

DIALOGIC ASSUMES NO LIABILITY WHATSOEVER, AND DIALOGIC

DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO

SALE AND/OR USE OF DIALOGIC PRODUCTS INCLUDING

LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A

PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT

OF ANY INTELLECTUAL PROPERTY RIGHT OF A THIRD PARTY.

Dialogic products are not intended for use in medical, life saving, life

sustaining, critical control or safety systems, or in nuclear facility

applications.

It is possible that the use or implementation of any one of the concepts,

applications, or ideas described in this document, in marketing collateral

produced by or on web pages maintained by Dialogic may infringe one or

more patents or other intellectual property rights owned by third parties.

Dialogic does not provide any intellectual property licenses with the sale of

Dialogic products other than a license to use such product in accordance with

intellectual property owned or validly licensed by Dialogic and no such

licenses are provided except pursuant to a signed agreement with Dialogic.

More detailed information about such intellectual property is available from

Dialogic's legal department at 9800 Cavendish Blvd., 5

Quebec, Canada H4M 2V9. Dialogic encourages all users of its products to

Pro™

procure all necessary intellectual property licenses required to

implement any concepts or applications and does not condone or

encourage any intellectual property infringement and disclaims any

responsibility related thereto. These intellectual property licenses may

differ from country to country and it is the responsibility of those who

develop the concepts or applications to be aware of and comply with

different national license requirements.

Dialogic, Diva, Eicon, Eicon Networks, Eiconcard, Dialogic Pro and

SIPcontrol, among others, are either registered trademarks or trademarks of

Dialogic. Dialogic's trademarks may be used publicly only with permission

from Dialogic. Such permission may only be granted by Dialogic's legal

department at 9800 Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada

H4M 2V9. Any authorized use of Dialogic's trademarks will be subject to full

respect of the trademark guidelines published by Dialogic from time to time

and any use of Dialogic's trademarks requires proper acknowledgement. The

names of actual companies and products mentioned herein are the trademarks

of their respective owners.

Floor, Montreal,