AQUAPHOR S550 Руководство по эксплуатации - Страница 13
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Диспенсер для воды AQUAPHOR S550. AQUAPHOR S550 20 страниц.
Печатать страницу
Mode of enhanced
washing from iron
Step 1. Turning on / off the enhanced iron
washing mode
Press and hold
to turn the feature on or off. In the mode
of enhanced washing from iron, a more intensive washing
of the softener with saline occurs, which contributes to
more efficient cleaning of the sorbent from iron. When this
mode is enabled, regeneration occurs every other day. To
achieve the desired effect, the mode of enhanced iron
washing should be switched on for at least 2 weeks. De-
pending on the iron content of the water, it is recommend-
ed to carry out this procedure at least once a year.
Advanced settings
Advanced settings allow you to select the brine regener-
ation mode, turn on the 96h mode, change the liter/gallon
and mg/L/gpg units, and set the regeneration start time.
Please be careful when using advanced settings.
Salt regeneration mode change
A. Press and hold
controller will beep and display the brine regenera-
tion mode on the display.
B. Press
to cycle through AU, HC, and HE modes.
Press
to save the selected option and proceed
to step 2.
Salt regeneration modes:
AU (Auto mode) – in this mode, the controller monitors
the daily water consumption and regulates the
amount of salt for regeneration. If the 96h mode is
disabled, the controller will regenerate 2 times a
week if there is water demand.
HC (High capacity mode) – fixed setting of salt regen-
eration, which allows less frequent washing of the
sorbent.
HE (High economy mode) – fixed salt regeneration set-
ting, which reduces the amount of water to be treat-
ed between flushes, but significantly saves salt.
Enabling / Disabling the forced regeneration mode "72-
96 hours"
In this mode, the controller will regenerate automatically,
at the appointed time once every 3–4 days, if normal
regeneration did not occur during this interval.
Press
to turn 96h mode on or off. The display on the
right side will show or turn off the indicator 96h. Click
to save your settings and move on to the next step.
96h mode. Activation of the 96h mode ensures that the
regeneration process is carried out at least 2 times
a week. This mode must be switched on if there is iron
and/or manganese in the source water.
and
for about 4 seconds, the
NOTE: More frequent regenerations help the softener to
recover more effectively from iron.
Unit switching: gallon / liter
Press C to switch gallon/liter units. The changes will be
displayed on the screen as gallons or liters. Click
save your settings and move on to the next step.
Setting the regeneration start time
A. Press
to set/change regeneration start time
(hours). Press
to save the settings and go to the
minutes setting.
B. Press
to change the minutes at which regener-
ation starts. Click
the home screen.
NOTE: Time is shown in 24 hour format.
Recommendations for
effective use softener
To get the most out of your softener, follow these
guidelines:
• Add salt if the level is below the water level in the
brine tank. The salt level must always be at least 1/3
of the full load.
• It is recommended to use pure salt in tablets or gran-
ules. Don't use rock salt.
• Once every 6 months it is recommended to use an ion
exchanger cleaner.
ATTENTION! Do not mix different types of salt.
• In the event of a power outage, check the correctness
of the controller settings (type of regeneration, water
parameters, time); if necessary, set the correct values.
(See the Controller Setup section).
• Program the softener to regenerate at times of the
day when you don't normally use water. If you have
several water treatment devices that require regener-
ation, the time between device regenerations should
be at least two hours.
• Please note that other water-using devices, such as
washing machines and dishwashers, should not be
running while the softener is regenerating.
• Protect the softener from freezing, including the drain
line.
• Follow the requirements for operation, maintenance
and placement of the softener.
• If the softener runs out of salt during operation: add
salt; wait at least two hours for the salt to dissolve and
then start the regeneration. To do this, press and hold
the R button for 5 seconds; regeneration will be com-
pleted in approximately 30–40 minutes, after which
the softener will return to normal operation.
to save the settings and go to
to
13