Burks 104300 Руководство по установке и эксплуатации - Страница 2

Просмотреть онлайн или скачать pdf Руководство по установке и эксплуатации для Системы смазки Burks 104300. Burks 104300 12 страниц.

Печатать страницу

Please Read This Before Installing Or Operating Pump.

This information is provided for SAFETY and to PREVENT

EQUIPMENT PROBLEMS. To help recognize this information,

observe the following symbols:

IMPORTANT! Warns about hazards that can result

in personal injury orIndicates factors concerned with

assembly, installation, operation, or maintenance which

could result in damage to the machine or equipment if

ignored.

CAUTION! Warns about hazards that can or will cause minor

personal injury or property damage if ignored. Used with symbols

below.

WARNING! Warns about hazards that can or will cause serious

personal injury, death, or major property damage if ignored. Used

with symbols below.

Hazardous ﬂ uids can

cause ﬁ re or explo-

sions, burnes or death

could result.

Biohazard can cause

serious personal injury.

Rotating machinery

Amputation or severe

laceration can result.

Only qualiﬁ ed personnel should install, operate and repair

pump. Any wiring of pumps should be performed by a qualiﬁ ed

electrician.

WARNING ! To reduce risk of electrical shock, pumps and

control panels must be properly grounded in accordance

with the National Electric Code (NEC) or the Canadian

Electrical Code (CEC) and all applicable state, province,

local codes and ordinances. Improper grounding voids

warranty.

WARNING! To reduce risk of electrical shock, always

disconnect the pump from the power source before

handling or servicing. Lock out power and tag.

WARNING! Operation against a closed

discharge valve will cause premature bearing

and seal failure on any pump, and on end

suction and self priming pump the heat build

may cause the generation of steam with resulting dangerous

pressures. It is recommended that a high case temperature

switch or pressure relief valve be installed on the pump body.

CAUTION ! Pumps build up heat and pressure

during operation-allow time for pumps to cool

before handling or servicing.

WARNING ! This pump is designed to handle materials

which could cause illness or desease through direct

exposure. Wear adequate protective clothing when

working on the pump or piping.

WARNING ! Do not pump hazardous materials

(ﬂ ammable, caustic, etc.) unless the pump is speciﬁ cally

designed and designated to handle them.

Other brand and product names are trademarks or registered trademarks of their respective holders.

®Burks is a registered trademark of Crane Pumps & Systems, Inc.

2003, 1/2006, 9/06, 3/07

SAFETY FIRST!

Extremely hot - Severe

burnes can occur on contact.

Hazardous ﬂ uids can Hazard-

ous pressure, eruptions or ex-

plosions could cause personal

injury or property damage.

Hazardous voltage can

shock, burn or cause death.

WARNING ! Do not wear loose clothing that may

become entangled in moving parts.

WARNING ! Keep clear of suction and discharge

openings. DO NOT insert ﬁ ngers in pump with power

connected.

Always wear eye protection when working on pumps.

Make sure lifting handles are securely fastened each

time before lifting. DO NOT operate pump without safety

devices in place. Always replace safety devices that

have been removed during service or repair. Secure the

pump in its operating position so it can not tip over, fall

or slide.

DO NOT exceed manufacturers recommendation for

maximum performance, as this could cause the motor

to overheat.

WARNING ! To reduce risk of electrical shock, all wiring

and junction connections should be made per the NEC

or CEC and applicable state or province and

codes. Requirements may vary depending on usage

and location.

WARNING! Products returned must be cleaned,

sanitized, or decontaminated as necessary prior to

shipment, to insure that employees will not be exposed

to health hazards in handling said material. All Applicable

Laws And Regulations Shall Apply.

Bronze/brass and bronze/brass ﬁ tted pumps may

contain lead levels higher than considered safe for

potable water systems. Lead is known to cause cancer

and birth defects or other reproductive harm. Various

government agencies have determined that leaded

copper alloys should not be used in potable water

applications. For non-leaded copper alloy materials of

construction, please contact factory.

Crane Pumps & Systems, Inc. is not responsible for

losses, injury, or death resulting from a failure to observe

these safety precautions, misuse or abuse of pumps or

equipment.

local