AQUARAY AQUABEAM Инструкция по установке и использованию - Страница 2

Просмотреть онлайн или скачать pdf Инструкция по установке и использованию для Осветительное оборудование AQUARAY AQUABEAM. AQUARAY AQUABEAM 6 страниц. Solid state lighting systems

Печатать страницу

AQUARAY

INSTRUCTIONS FOR INST LL TION ND USE

Important Safety Information - Please Read Carefully

- AquaRay Solid State Lighting systems comprise an AquaRay lamp unit with

a separate mains power supply unit (PSU) which supplies a constant DC

(low voltage) power supply to the lamp unit.

Power supply for AquaBeam/GroBeam Lighting Strip Single lamp unit:

INPUT-100-240 VAC 50-60Hz 0.15A OUTPUT-19.5 VDC 0.7A

Power supply for AquaBeam/GroBeam Lighting Strip Twin lamp unit:

INPUT-100-240VAC 50-60Hz 0.3A OUTPUT 1-19.5VDC 0.7A

OUTPUT 2-19.5 VDC 0.7A

Power supply for AquaBeam/GroBeam Lighting Tile:

INPUT-100-240VAC 50-60Hz 0.3A OUTPUT 1-19.5VDC 0.7A

OUTPUT 2-19.5 VDC 0.7A

Caution: Do not use any other power supply unit with an AquaRay lamp unit as

the lamp unit may not work and this may cause irreparable damage to the lamp

unit. If the PSU supplied with the unit needs to be replaced then please obtain an

authentic AquaRay PSU supplied by one of Tropical Marine Centre's

local stockists.

- Always isolate the PSU from the mains electricity before installing or

carrying out any maintenance to the AquaRay lamp unit.

Caution: The power supply unit (PSU) is not waterproof and

therefore must not be mounted above the aquarium or in any

position where it may accidentally fall into water or be splashed by

water.

Caution: Do not position the PSU in an enclosed space. Ventilation must be

provided to ensure it does not overheat.

Caution: Do not operate this appliance if any part of it has a damaged cord or

plug, is malfunctioning, or has been dropped, immersed in water or damaged in any

way. If the external cord of this unit is damaged, it should be replaced by a cord

exclusively available from the manufacturer or his service agent.

- This unit is designed to be used indoors and is not suitable for any

outdoor applications.

Caution: Ensure the AquaRay lamp unit is securely installed above the

tank before operating.

Caution: The AquaRay lamp must be installed no less than 25mm

from the water surface.

Caution: DO NOT SUBMERGE THE AQUARAY LAMP UNIT. If the unit is

submerged the lamp unit guarantee will be invalidated.

Caution: Always leave a drip-loop in the DC supply cable to the AquaRay lamp

unit to prevent water running down the cable and reaching the PSU (see picture below).

- When in operation, the grooved aluminium heat sink on the back of the AquaRay

lamp unit will get hot (± 60°C) to the touch. This is normal and is an essential

feature of protecting the lamp unit from over-heating.

Caution: Do not cover, or obstruct in any way, the rear aluminium surface of the

AquaRay lamp unit which should always have a minimum of 10mm clearance from

the nearest surface to allow free circulation of air around it.

Caution: Operation of the AquaRay unit in a confined or unventilated space, or

where there is an additional heat source, could cause the ambient

operating temperature to rise above 35°C, reducing the useable life

of the unit.

- Dispose of this unit responsibly. Check with your local authority for

disposal information.

The quaRay lamp unit is mercury free.

PRODUCT INFORM TION

- This unit is manufactured and conforms to:-

Safety: BS EN 60598-1: 2000. BS EN 60598-2-11: 2005

EMC: BS EN 55015: 2001. BS EN 61000-3-2: 2006.

- This unit is CE approved.

quaBeam/GroBeam Lighting Strip

Typical Installation

quaBeam/GroBeam Lighting Tile

Solid State Lighting Systems

Aquarium

Drip-loop