AquaScape 77005 Инструкции по установке

Просмотреть онлайн или скачать pdf Инструкции по установке для Системы фильтрации воды AquaScape 77005. AquaScape 77005 2 страницы. Container water garden filter

Печатать страницу

I N S T A L L A T I O N

CONTAINER WATER GARDEN FILTER

Container Water Garden Filter

Item #77005

Contents

No.

Description

Filter

Spray Bar

Safety Information

WARNING: Risk of electric shock – This pump has not been approved for use in

swimming pool or marine areas.

WARNING: To provide continued protection against risk of electric shock, connect to

properly grounded, ground fault circuit interrupter (GFCI) outlets only, using the following

guidelines:

(A) Have a qualified electrician install a properly grounded receptacle outlet, acceptable for outdoor

use and protected from snow and rain.

(B) Inspect cord before using.

(D) Any wiring of pumps should be performed by a qualified electrician to ensure code compliance

and user safety.

(E) Unplug pump at receptacle outlet when not in use or before removal from pond.

(F) To reduce risk of electrical shock, all wiring and junction connections should be made per local

codes. Requirements may vary depending on usage and location.

(G) The power cable should be protected at all times to avoid punctures, cuts, bruises and

abrasions.

(H) Never handle power cords with wet hands.

(I) Do not remove cord and strain relief. Do not connect conduit to pump.

(J) Do not use power cable to lift pump.

• Always operate the pump fully submerged. Failure to do so may overheat the pump and cause it to

fail, voiding the warranty. DO NOT OPERATE DRY!

• Use only in fully assembled state. Failure to operate the pump without the cover/strainer in place

will allow large debris to enter the pump, causing the pump to fail and voiding the warranty.

• Do not wear loose clothing that may become entangled in the impeller or other moving parts.

• Keep clear of suction and discharge openings. DO NOT insert fingers into pump with power

connected.

• Do not pump hazardous materials or liquids, such as oil, saltwater or organic solvents.

• Products returned must be cleaned, sanitized, or decontaminated, as necessary, prior to shipment

to ensure that employees will not be exposed to health hazards in handling said material. All

applicable laws and regulations shall apply.

IMPORTANT: Aquascape, Inc. is not responsible for losses, injury, or death resulting from

a failure to observe these safety precautions, misuse or abuse of pumps or equipment.

Container Water Garden Filter Specifications

• Input Voltage: 120V AC

• Input Frequency: 60 Hz

• Flow: 100 GPH/2.98 ft max head

• For outdoor or indoor use

Installation

• The Aquascape Container Water Garden Filter is sized

and designed for small to medium-sized water features

up to approximately 50 gallons. It's small enough to

fit into tight spaces (Ex. 1), yet contains everything

you need to filter the water: a pump, mechanical

filter sponge, and biological carbon media.

facebook.com/aquascapeinc

youtube.com/aquascape4

pinterest.com/aquascapeinc

• This pump has been evaluated for use

with freshwater only

• Input Amps and Wattage: 0.06A/7 Watts

I N S T R U C T I O N S

• The Aquascape Container Water Garden Filter is designed

to be operated fully submerged (Ex. 2). DO NOT RUN DRY.

Add either the spray bar or hose barb attachment to the

filter discharge:

• Spray Bar: The spray bar will ensure circulation and water

movement necessary for proper aeration when keeping fish.

• Attach the threaded elbow portion of the spray bar kit directly

to the Aquascape Container Water Garden Filter (Ex. 3), then

add the remaining two pieces of the spray bar (Ex. 4). The

far end of the spray bar is sealed with a circular rubber plug.

(To position the spray bar farther from the pump add the

extension between the

threaded elbow and the

slip X slip elbow.)

• Position the spray

bar horizontally at the

surface of the water.

• Hose Barb Attachment:

The hose barb

attachment allows you

to use the Aquascape

Container Water

Garden Filter to run a

variety of ornaments

or accessories. Attach the threaded portion of the hose barb

directly to the filter and then attach the hose running from the

ornament to the hose barb (Ex. 5).

• The filter can be placed in either the horizontal position on the

shelf of the container water garden, or vertically or horizontally

on the bottom of the container.

• Connect the filter to an outlet that is protected by a ground

fault circuit interrupter (GFCI).

• Once the filter is running and water circulating, check for any

fitting leaks.

General Maintenance

• Component Parts Cleaning

– The filter cartridge is easily separated from the pump for maintenance purposes. Grasp the pump

in one hand and gently pull while bending the filter cartridge away from the pump. It will pop off,

allowing access to both the filter carbon cartridge and the filter sponge.

• Inlet Screen and Filter Cleaning

– We recommend inspecting your pump on a regular basis to ensure it is functioning properly. If

you notice the water flow rate diminish, it may be due to the pump's inlet screen or internal filters

becoming clogged with debris. In many cases the clogged screen can be cleaned by pulling the

pump out of the water to remove debris from the pump cover. With the filter sponge and carbon

cartridge removed, rinse them in a bucket, using clean water from your container water garden to

dislodge debris. Always disconnect the power before performing maintenance on the pump.

• Internal Pump Cleaning

– If you have thoroughly cleaned the intake screen and filters and still have diminished flow rates,

then you will need to remove the impeller cover to inspect the impeller rotor assembly.

– If your rotor assembly impeller and internal pump body have excessive scale build-up, clean with

a mild acid, such as white vinegar or non-abrasive calcium, lime and rust remover product using

a sponge or soft-bristled brush that won't scratch the impeller. Removing scale build-up will alow

your pump to run like new again.

• Replacing the Impeller Assembly

– The impeller assembly is the only moving part on the pump and will experience wear and tear. If

you've cleaned the pump, as described above, and still experience poor pump performance, it

is most likely time to replace the impeller. Replacing the impeller is extremely easy. Replacement

Impeller Kits are available through your local Aquascape dealer.

Winter Application

• Disconnect the tubing from the discharge fitting and remove the pump from the container water

garden. Clean the pump and inlet screens with fresh water and store the pump in a frost-free location.

Troubleshooting

• Reduced Water Flow

– Pump or plumbing may be clogged. It may be necessary to clean the pump intake screen,

internal filters, and impeller.

• Pump Hums and Doesn't Push Water

– Pump or plumbing may be clogged. It may be necessary to clean the pump intake screen,

internal filters, and impeller.

– Remove the filter cartridge and impeller cover and inspect and clean the impeller rotor assembly

and internal pump body.

– Make sure nothing is blocking or wrapped around the impeller.

– Make sure the pump is receiving the correct voltage.

• Pump Not Working

– The ground-fault circuit-interrupter (GFCI) may have tripped.

– The pump is not receiving the correct voltage.

Ex. 1

For more information about our company or products, please visit our website at

aquascapeinc.com or call us at US (866) 877-6637 CAN (866) 766-3426

Ex. 2

Ex. 3

Ex. 4

Ex. 5

01/05/23