AquaScape 84060 Руководство по установке - Страница 3

Просмотреть онлайн или скачать pdf Руководство по установке для Осветительное оборудование AquaScape 84060. AquaScape 84060 6 страниц. Color-changing lights
Также для AquaScape 84060: Руководство по установке (6 страниц)

Печатать страницу

AquaScape 84060 Руководство по установке

WARNING: Do not submerge quick-connect fittings, as

moisture entering the connections will damage the lights.

COLOR-CHANGING LIGHTING CONTROL HUB

• The Aquascape Color-Changing Lighting Control Hub (not included) is

required to power and control Aquascape color-changing lights (Ex. 9).

• Connect the light, splitter, or extension to the 5-pin quick-connect fitting

attached to the hub (Ex. 10).

Ex. 9

NOTE: Each control hub can control up to 150-watts of color-changing

lights.

NOTE: Only one remote can be paired to a single hub.

NOTE: Multiple Color-Changing Lighting Hubs and remotes can be used

to assign multiple colors simultaneously.

NOTE: The control hub is weather resistant, but not waterproof. Install it

off the ground and protected from the elements.

TRANSFORMER SETUP

• Aquascape color-changing lights are designed to operate on a 12-volt,

outdoor-rated transformer.

WARNING: Aquascape color-changing lights have a max

voltage operating range between 10.8 and 15 volts. Operating

the light outside of this voltage range voids the product warranty

and may damage or shorten the life of the light.

NOTE: It is recommended to

locate the transformer as close

to the light fixtures as possible to

avoid voltage drops caused by

long cable runs.

• Plug the transformer into a GFCI-

protected outlet (Ex. 11).

REMOTE CONTROL PAIRING

• Each control hub includes a

wireless remote control. Install two

AAA batteries (not included) in the

back of the remote control.

• To synch the remote control to the hub, hold the power button on the

remote while connecting the 2-pin quick-connect fitting on the hub to the

transformer (Ex. 12).

aquascapeinc.com |

☎

CAN (866) 766-3426 |

• All lights plugged into the control hub will flash green when paired.

• Once the remote is synched to the control hub, bury or conceal any

visible cables. It is recommended to bury light cables no deeper than 6".

REMOTE CONTROL FUNCTIONS

• Power/Pair – Turn lights on and off as desired. Also use this button to pair

the remote to the hub.

• Color Wheel – Select your desired color

• Rate/Speed Up – Increase the speed of the cycle or strobe option

• Rate/Speed Down – Decrease the speed of the cycle or strobe option

• Select Mode – Stops the cycle or strobe to achieve the desired color

• Undo Mode – Revert back to the cycle or strobe last selected

• Brightness Up – Increase the brightness

• Brightness Down – Decrease the brightness

• Cycle – Continuously changes through all available color options

• White – Engages the white diodes for a warm white light (3,000 K)

• Strobe – Select between a variety of strobe options

Ex. 10

General Maintenance

• Periodically clean the fixture with fresh water, removing any existing algae,

debris, or buildup.

Troubleshooting

• Lights won't turn on

– Press the power button on the remote

– Make sure the outlet is receiving power

– Make sure the ground-fault circuit interrupter (GFCI) is not tripped

– Check to verify that the lights are receiving the correct voltage

– Verify that the photocell is functioning properly

• Lights won't turn off

– Verify that the photocell (not included) is functioning properly

• Remote Control is not functioning

– Make sure the AAA batteries are not dead

– Re-synch the remote control to the lighting control hub

Replacement Parts

No.

Item number/description

84037 - Waterfall and Up Light Replacement Base

84036 - 4.5/8-Watt LED Color-Changing Spotlight Replacement

Mounting Kit

Warranty Information

Ex. 11

Aquascape LED Color-Changing Lighting is guaranteed for five years from

date of purchase. Proof of purchase required. Warranty does not cover

damage resulting from negligent handling, misuse or lack of care. Light failure

as a result of improper wiring is not covered under warranty. Lights should

only be operated in fresh water without corrosive chemicals like chlorine or

bromine. Warranty is valid against defects due to material and workmanship

only. Products returned must be cleaned, sanitized, or decontaminated, as

necessary, prior to shipment to ensure that employees will not be exposed to

health hazards in handling said material. All applicable laws and regulations

shall apply. The sole obligation shall be to replace the defective unit with a

suitable replacement unit. Units should be checked for proper operation prior

to returning as defective. No liability for loss or damage of any nature or kind,

whether arising out of or from the use of the product, whether defective or not

Ex. 12

For more information about our company or products, please visit our website at

aquascapeinc.com or call us at US (866) 877-6637 CAN (866) 766-3426

11/18

☎

US (866) 877-6637

LED Color-Changing Lights Replacement Parts

5 YEAR WARRANTY

defective, is assumed by Aquascape, Inc. or it's affiliates.