Chuango SMK-500 Руководство пользователя - Страница 2

Просмотреть онлайн или скачать pdf Руководство пользователя для Дымовая сигнализация Chuango SMK-500. Chuango SMK-500 3 страницы. Smoke detector wireless and independent
Также для Chuango SMK-500: Руководство пользователя (2 страниц)

Печатать страницу

Installing Your Smoke Detectors

Read"Locations to Install Your Smoke Detectors" and "Locations not to Install

Your Smoke Detectors" section in the manual first, and then decide where to

install the detector.

Please follow these steps to install your smoke detector:

At the place where you are going to install the detector, draw a horizontal line

six inches long.

Remove the mounting bracket from your unit by rotating it counterclockwise.

Place the bracket so that the two longest hole slots are aligned on the line. In

each of keyhole slots, draw a mark to locate a mounting plug and screw.

Remove the bracket.

Using a 3/16-inch (5mm) drill bit, drills two holes at the marks and insert

plastic wall plugs. Put the detector away from getting plaster dust on it when

you drill holes for mounting.

Using the two screws and plastic wall plugs (all supplied), attach the bracket to

the wall.

Line up the slot of the bracket and the detector. Push the clockwise to fix it

into place. Pull outward on the detector to make sure it is securely attached to

the mounting bracket.

BRACKET

DETECTOR

SCREWS

The steps to open the battery cover and to install the battery are listed as

follows:

To power smoke detector requires a battery.

(1)

(2)

Match terminals on the end(s) of the battery with opposite terminal

connections on the detector. Be sure to insert the zinc-manganese dry

battery in the position shown on the detector.

(3)

When terminals are properly matched, push battery firmly in until it snaps

and cannot be shaken loose.

BATTERY

CAUTION:

This smoke detector comes with cover latches that will prevent the

smoke detector cover from closing if battery is not installed. This tells you that

the smoke detector will not work until a new battery is properly installed. The

battery is purposely positioned WRONGLY in the factory to keep it fresh

until installation. It must be re-positioned correctly to provide DC power.

NOTE:

When the detector battery first makes contact with the detector, the

alarm horn may sound for one second. This is normal and indicates that the

battery is positioned properly. Close cover, then press the test button, holding

it down for about 5 seconds until the horn sounds. The horn should sound a

loud, pulsating alarm. This means the unit is working properly.

LOUDSPEAKER

RED LED

TESTING BUTTON

Connect with Alarm Control Panel

SMK-500 can not only work as a single station, but also can work with alarm

control panel to form an alarm system when wireless module is added to the

smoke detector.

1) Make sure the control panel is in learning state.

2) Press the testing button on the smoke detector for 3 seconds, two beeps

are heard. Simultaneously, one beep is heard from the control panel. The

detector has been connected successfully with the control panel.

Testing:

Press the testing button on the smoke detector for 3 seconds, the control

panel will alarm immediately.

Red LED Indicator

The red LED, as the ALARM indicator, is featured with the detector. It can be

seen through the test button on the cover of the detector. When red LED

flashes once 32 seconds, it indicates the detector under normal operation.

When smoke detector senses smoke and simultaneously sounds an audible

alarm, the red LED will flash very frequently, once 0.67 seconds.

Testing Your Smoke Detector

Test the detector weekly by pushing firmly on the test button with your finger

until the horn sounds. Testing method may take up to 5 seconds to sound the

alarm horn. These are only ways to be sure that detector is working correctly.

If the detector fails to test properly, have it repaired or replaced immediately.

WARNING:

Never use an open flame to test your detector. You may set fire to

damage the detector, as well as your home. The built-in test switch accurately

tests all detector functions, as required by Underwriters' Laboratories. They

are the only correct ways to test the unit.

WARNING:

When you are not testing the unit and the alarm horn sounds a

loud continuous sound, this means the detector has sensed smoke or

combustion particles in the air. Be sure that the alarm horn is a warning of a

possible serious situation, which requires your immediate attention.

The alarm could be caused by a nuisance situation. Cooking smoke or a dusty

furnace, sometimes called "friendly fires" can cause the alarm to sound. If this

happens, open a window or fan the air to remove the smoke or dust. The

alarm will turn off as soon as the air is completely clear.

NOTE:

Do not disconnect the battery from the detector. This will remove your

protection from fires.

Using The Silence Feature

The silence feature can temporarily quiet an unwanted alarm for up to 8

minutes. To use the feature, press the"TEST" button .When remain in silence,

the LED will flash once every 8 seconds (for up to 8 minutes) to remind you

the alarm has been stopped. The flashing LED will stop when the unit returns

to normal operation.

WARNING: The silence feature does not disable the unit. It is temporarily less

sensitive to smoke. For your safety, if smoke around the unit is dense enough

to suggest a potentially dangerous situation, it will stay in alarm, or may re-

alarm quickly. If you do not know the source of the smoke, do not assume it is

an unwanted alarm. Not responding to an alarm can result in property loss,

injury or death.

NOTE: Do not disconnect the battery from the detector. This will remove your

protection from fires.

If a beep or chirp virtually simultaneously with an LED flash once a minute,

this means the detector 's battery is weak. Replace new battery immediately.

If a beep or chirp occurring halfway an LED flash once a minute, this signal

means that the detector is faulting, it is must repaired or replaced

immediately.

Taking Care of Your Smoke Detector

To keep your detector in good working condition, you must test the detector

weekly, as referring to section "TESTING YOUR SMOKE DETECTOR".

Replace the detector battery when the low battery "beep" signal sounds once

a minute. The low battery "beep" should last at least 30 days.

NOTE:

For replacement battery, use Gold Peak 1604P , 1604S, 1604G, 1604A;

Eveready522, 216; Duracel Mn1604; PremisafeG6F22; UltralifeU9VL-J; EVE

CR9V.

WARNING:

Do not use any other kind of battery. This detector may not

operate properly with other kind of battery.

Open the cover and vacuum the dust off the detector 's sensing chamber at

least once a year. This can be done when you open the detector to change

the battery. Remove battery before cleaning. To clean detector, use soft brush

attachment to your vacuum. Carefully remove any dust on detector

components, especially on the openings of the sensing chamber. Replace

battery after cleaning. Test detector to make sure battery works correctly.

Check to make sure there is no obstruction inside the test button. If there is

any dust in the test button, insert a toothpick from the back to the front.

NOTE:

If nuisance alarms keep coming from the detector, you should check

whether the detector 's location is adequate. Refer to section "WHERE TO

INSTALL SMOKE DETECTORS." Move your detector if it is not located properly.

Clean detector as described above.

Clean detector cover when it gets dirty. First open the cover and remove

battery. Hand-wash cover with cloth dampened with clean water. Dry it with

lint-free cloth. Do not get any water on the detector components. Replace the

battery, and close cover. Test detector to make sure that battery works

correctly.

Technical Specifications

Power Supply:

DC 9V 6F22 batter y x 1

Standby Current:

≤

5uA

Alarm Current:

≤15mA

LED Frequency in Working State:

Once ever y 32 sec.

LED Frequency in Alarming State:

Once ever y 0.62 sec.

Low Battery State:

Beep once with a LED flash per 60s (last for 30 days)

Operation Condition

Temperature: -10°C ~ +55°C

Relative humidity: ≤95%(no condensing)

Monitoring Area:

20m

Alarm Decibel:

85dB/3m

Radio Frequency:

315MHz, 433.92MHz or 868MHz

Transmitting Distance:

≤

80m in open area(SMK-500)

Housing Material:

ABS plastic

Dimensions (L x W x H) :

102x102x31mm

Ver : SMK-500-EN-1405-V2.0