Aquatec Equipment EV3910LV-DC Руководство по эксплуатации - Страница 5
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Водяной насос Aquatec Equipment EV3910LV-DC. Aquatec Equipment EV3910LV-DC 13 страниц. Low voltage submersible water pump & dc power supply
Печатать страницуINSTALLATION
For your convenience we have provided two different front filter cages. One has a built in flow control, that can be used
to adjust the water flow if the flow is too fast for a particular installation. This is used in clean waterfeatures, where a
"filter-less" system is preferable.
The other Filter Cage contains a sponge filter insert. This filter is to be connected to the front of the pump to strain out
the larger particles when using a fountain kit. This reduces the frequency of having to clean. If using an optional fountain
kit, select the filter cage with the sponge insert. Some may choose to upgrade to a F11 Block sponge that has an even
larger surface area, which does not need to be cleaned as often.
This is a low voltage 12V DC System. To connect, push the 2 Pin Connector into the DC Power Supply. Then connect the
240V plug to the power supply.
FOUNTAIN KIT SETUP GUIDE
A basic plastic fountain kit is not recommended for pumps that have flow over 6000L/hour. It's better to use
commercial fountain nozzles for higher flow. See your dealer for examples.
For Pumps, from 850L/hour to 5000L/hour, there are a number of optional fountain kits readily available. Pondmax has
three readily available. For various suggestions of the correct model and fountain type selection see the specification
table on page (page 2).
For the purpose of these guidelines, a Pondmax #30 Jet kit has been selected. The installation principle will be similar for
the other types.
Using the 1" to ½" threaded reducing nipple, locking nut & O'ring (1),
attach onto the Male Threaded outlet of the pump. Now secure the
Duel-Control-T-Piece (2) onto threaded reducing nipple. Now on the
top of the Duel-Control-T-Piece (2), connect the Reducing Adaptor (4)
on. Now extend riser to the desired height, then secure onto the top of
the Reducing Adaptor with the threaded locking nut provided. Align
riser vertically.
Select the desired nozzle, (7) (8) or (9), and screw into the Fountain
Nozzle Threaded Mount. (6) Then attach the Mount to the riser.
Locate the stepped hose tail (5). Attach this to the side outlet of the
Duel-Control-T-Piece to facilitate an optional accessory for example
a filter or waterfall. Now, utilizing the Flow-Adjustment-Knob (3), on
the T-Piece, you can vary the flow between the fountain head and the
waterfall outlet. Close the second outlet of the T-Piece if this is not
required. Now connect tubing to the side Hosetail if required. This
T-piece is not suitable for dry mount applications.
Place the pump in desired location; ensure the pump is on a stable
surface that is free of sludge, sand and other debris. Position the device
in the pond horizontally, on a solid base, in such a way that it is fully
covered with water and ensure that the pump is located, at a depth,
in the water, which will not allow it to suck air from the surface. This is
known as cavitation. Cavitation is a cause of premature impellor wear.
The fountain nozzle should now be protruding out of the water.
Push the plug into the power supply outlet and switch on. Use the
power supply switch for turning the unit on and off.
PMAX EVOII 1910_2910_3910_4910 DC Pump Instructions.indd 5
7. Fine Daisy
8. Coarse Daisy
Fountain Nozzle
Fountain Nozzle
W A T E R G A R D E N I N G T O T H E M A X
SUBMERSIBLE
WATER PUMPS
6. Fountain
Nozzle Threaded
Mount
Telescopic Riser
4. Threaded Locking Nut &
1" Threaded to 1/2 Threaded
Reducing Adaptor
2. Dual Control
T-Piece
3. Flow Adjustor
9. Bell Fountain
Fountain Nozzle
5. Stepped Hosetail
1. Reducing nipple,
Locking Nut &
O'Ring
22/12/16 7:33 am