Diamond Products CC800M Руководство по эксплуатации - Страница 3
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Пила Diamond Products CC800M. Diamond Products CC800M 8 страниц. Core cut masonry saw
Печатать страницу
OPERATING INSTRUCTIONS:
BLADE MOUNTING:
1.
Be certain that
you
service
dealer for
difference in your blade costs
2.
The blade
shaft
Using
the
wrench
parts immediately.
attempting
to mount blade.
3.
Mount
the blade
the
arrow
on
the blade
tighten
blade shaft bolt very
bolt has left hand threads,
BEFORE SAWING:
1.
After
mounting the
mounted. Blade exposure cannot exceed
WARNING: Never
2. Do
not use conventional (wet) diamond blades
water per minute flowing
sawing, be sure the
has
an
adequate supply of water.
to saw.
SAW
OPERATION:
1.
Place
the
saw
cannot
fall
over.
WARNING: Be certain that
result in bodily injury.
..,
The cutting operation:
a) To
cut wet:
Electric
motor
submerged at al l times.
motor is
switched on. Do
blade
guard,
minute) to
adequately cool wet cutting
Gas
engine –
should
flow
b) To cut dry:
Electric
motor
water
valve on
Gas engine
WARNING:
Only cut dry with
protection.
For Saws
With
c)
Connect
motor to
motor capacitor
match
correct voltage.
have
the correct diamond
the
correct specification. Getting the correct blade will
and
performance.
flanges and arbor must
be inspected
provided,
remove
the
Inspect the blade for damage to the
solidly
and firmly
on
the
is
pointing in the proper direction
securely! (Approximately 50 foot
which
tightens
saw
blade, install proper size blade guard and check
operate the
saw
without proper blade
over
the blade for proper
spray
holes i n the
blade guard water
Test your
frame
on
a sturdy,
level
saw
frame would not tilt or fall over. Failure to do so may
-
Fill
water tub
within
Plug pump
into receptacle i n
not allow
pump to
and
check water flow
before
Engage water
pump
on
at 2
-
5 GPM (gallon per
- Disconnect
pump
blade
guard.
-
Disengage water pump on
adequate ventilation
Electric
Motors:
a properly grounded outlet.
housing to
match desired
blade
for the
application. Contact
for
damage and
outer
flange.
If
there
arbor hole
outer flange
arbor
and
of rotation.
pounds.)
by turning counter-clockwise.
1 80
degrees when
cutting.
guard in
without water! You
must have
cooling and
to
get
tubes
are open and
water
supply
for pressure and
surface.
Check to make
one
inch
of
top.
Place
motor
capacitor
run dry to
avoid
cutting. Water
should flow at
blades.
cutting head.
Open water valve fully
minute)
to
adequately cool wet cutting blades.
plug
from motor
outlet while motor
cutting
head.
Close
and proper respiratory
Motor
may be operated on
voltage.
Plug
on
your
authorized
made a
tremendous
cleaned
before mounting blade.
is
any damage
replace
and flange
area
then
to the
blade
shaft.
Using the
wrench
provided,
Note
that the blade
to
see
that it
is
securely
place!
2-1 /2
from
to 5 gallons
maximum blade life. For wet
that
each side
of
quantity
(flow)
before starting
sure
that the
saw
does not
pump
in
water tub
so
that
box. Pump will
damaging it. Open
water valve
2
-
5 GPM (gallons
before
cutting. Water
is
switched
OFF.
water valve
on
blade
guard.
230
460
or
motor cord
must
also be
the
bad
before
Make sure
shaft
of
the blade
tilt or
intake
is
fully
run
whenever
fully on
per
C
lose
volts.
Set
changed
to
3