Panasonic DLP PT-D12000U Брошюра и технические характеристики - Страница 6

Просмотреть онлайн или скачать pdf Брошюра и технические характеристики для Проектор Panasonic DLP PT-D12000U. Panasonic DLP PT-D12000U 6 страниц. 3-chip dlp projector
Также для Panasonic DLP PT-D12000U: Руководство по настройке и эксплуатации (37 страниц)

Печатать страницу

Panasonic DLP PT-D12000U Брошюра и технические характеристики

Specifications

Power supply

120–240 V AC 16–9A, 50Hz/60Hz

Power consumption

1,600–1,500 W (10–15 W in standby mode with fan stopped)

DLP

chip

Panel size

0.95" diagonal (4:3 aspect ratio)

Display method

DLP

chip x 3 (R, G, B), DLP

Pixels

1,470,000 (1,400 x 1,050) x 3, total of 4,410,000 pixels

Lens

Optional powered zoom/focus lenses

Lamp

300 W UHM™ lamp x 4 (four lamp system)

Screen size

70 - 600 inches,4:3 aspect ratio

(70-300 inches, 4:3 aspect ratio with the ET-D75LE5)

Brightness*

12,000 lumens (four-lamp operation mode)

Contrast ratio*

5,000:1 (full on/full off, in Dynamic iris 3 mode)

Resolution

1,400 x 1,050 pixels (1,920 x 1,200 pixels compatible, compression mode)

RGB input scanning frequency

15-100 kHz, fV 24-120 Hz

Dot clock 20-162 MHz

Component signal

480i, 480p, 576i, 576p, 720/60p, 720/50p, 1035/60i, 1080/25p, 1080/24p,

1080/24sF, 1080/30p, 1080/60i, 1080/50i, 1080/50p, 1080/60p

Video signal

15.75/15.63 kHz, fV 50/60Hz

(NTSC,NTSC4.43,PAL,PAL60,PAL-N,PAL-M,SECAM)

Lens shift

Vertical: ±50% (±40% with the ET-D75LE6) (powered)

Horizontal: ±30% (±20% with the ET-D75LE6) (powered)

Keystone correction range

Vertical: ±40° (±22° with the ET-D75LE5, ±28° with the ET-D75LE6),

Using Geometric Adjustment: Vertical ±10°, Horizontal ±15°

Terminals

DVI-D IN

DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, single link

480p, 576p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p,

720/60p, 720/50p

VGA (640 x 480) – WUXGA*

Dot clock: 25–162 MHz

RGB1/YP

BNC x 5

RGB2 IN

D-sub HD 15-pin x 1

VIDEO IN

BNC x 1, 1.0 Vp-p

VIDEO OUT

BNC x 1, 1.0 Vp-p

S-VIDEO IN

Mini DIN 4-pin x 1

LAN

RJ-45 (10 Base-T/100 Base-TX) x 1, compatible with PJLink™

SERIAL IN

D-sub 9-pin female x 2 (RS232C x 1, RS422 x 1)

SERIAL OUT

D-sub 9-pin male x 1 (RS422 x 1)

REMOTE 1 IN

M3 jack x1 for wired remote control

REMOTE 1 OUT

M3 jack x1 for link control

REMOTE 2 IN

D-sub 9-pin female x 1 for external control (parallel)

Optional board slot With ET-MD77SD1

SERIAL IN: BNC x 1, SD-SDI signal (YC

installed*

SERIAL OUT: BNC x 1, active through

With ET-MD77SD3

SERIAL IN: BNC x 1, SD-SDI signal (YC

installed*

Single-link HD-SDI signal (YC

1035/60i, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p

SERIAL OUT: BNC x 1, active through

With ET-MD100SD4

Link A/Link B IN: BNC x 1 for each, SD-SDI signal (YC

installed

Single-link HD-SDI signal (YC

1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p

Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE 372M compiant: 1920 x 1080/50i,

1920 x 1080/60i, 1920 x 1080/25p, 1920 x 1080/24p, 1920 x 1080/24sF, 1920 x 1080/30p

Dual-link HD-SDI signal (X'Y'Z' 4:4:4 12-bit): 2048 x 1080/24p, 2048 x 1080/24sF

Projection distance

Diagonal

ET-D75LE6

image size

1.0-1.2:1

(aspect raio: 4:3)

min.

max.

1,393 mm

1,662 mm

70"

4.6'

5.4'

2,014 mm

2,406 mm

100"

6.7'

7.8'

3,049 mm

3,646 mm

150"

10.0'

11.9'

4,084 mm

4,886 mm

200"

13.5'

16.0'

6,154 mm

7,366 mm

300"

20.2'

24.1'

8,224 mm

9,846 mm

400"

27.0'

32.2'

12,364 mm

14,806 mm

600"

40.6'

48.5'

NOTES ON USE

1. Do not install the projector in locations that are subject to excessive water, humidity, steam, or oily smoke. Doing so may result in fire, malfunction,

or electric shock.

2. The projector uses a high-voltage mercury lamp that contains high internal pressure. This lamp may break, emitting a large sound, or fail to

illuminate, due to impact or extended use.

3. The projector uses of high-wattage lamp that becomes very hot during operation. Please observe the following precautions.

• Never place objects on top of the projector while it is operation.

• Make sure there is an unobstructed space of 500 mm or more around the projector's exhaust openings.

• Do not stack projector units directly on top of one another for the purpose of multiple (stacked) projection.

When stacking projector units, be sure to provide the amount of space indicated between them. These space requirements also apply to

installation where only one projector unit is operating at one time and the other unit is used as a backup.

• If the projector is placed in a box or enclosure, temperature of the air surrounding the projector must be between 0°C and 35°C. Also make sure

the projector's intake and exhaust openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is not sucked

into the intake.

Panasonic Projector Systems Company,

Unit of Panasonic Corporation of North America

www.panasonic.com/projectors

Headquarters

Panasonic Canada Inc.

3 Panasonic Way, 4B-9

5770 Ambler Drive

Secaucus, NJ 07094

Mississauga, Ontario

888-411-1996

Canada L4W 2T3

905 624 5010

projection system

(1,920 x 1,200), compatible with non-interlaced signals only,

4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i

4:2:2 10-bit): SMPTE 292M compiant: 720/50p, 720/60p,

4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i

4:2:2 10-bit): SMPTE 292M compiant: 720/50p, 720/60p, 1080/50i,

ET-D75LE1

ET-D75LE2

1.5-2.0:1

2.0-3.0:1

min.

max.

min.

2,072 mm

2,768 mm

2,801 mm

6.9'

9.0'

9.2'

2,992 mm

3,998 mm

4,035 mm

9.9'

13.1'

13.3'

4,526 mm

6,047 mm

6,093 mm

14.8'

19.8'

19.9'

6,060 mm

8,096 mm

8,150 mm

19.9'

26.5'

26.8'

9,128 mm

12,194 mm

12,265 mm

30.0'

40.0'

40.3'

12,196 mm

16,292 mm

16,380 mm

40.1'

53.4'

53.8'

18,332 mm

24,488 mm

24,610 mm

60.2'

80.3'

80.8'

Optional board slot With ET-MD77DV

Specifications are the same as those for the DVI-D IN terminal on the main unit.

installed

Installation

Front/rear, ceiling/floor

Power cord length

9.9" (3.0 m)

Dimensions (W x H x D)

22-3/4" x 12-19/32" x 25-5/16" (578 x 320 x 643 mm) (without lens)

Weight*

Approx. 77.1 lbs (35 kg) without lens

Operating temperature

32 -113 °F (0 -45 °C)*

Operating humidity

10-80% (no condensation)

Supplied accessories

Power cord, Wireless/wired remote control unit,

Batteries for remote control (3V AA battery x2), Eye bolt x4, Wire rope

Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.

Only when using VESA CVT-RB(Reduced Blanking) signals.

The LAN terminal on each board, when mounted, cannot be used because the LAN terminal on the main unit has priority.

Average value. May differ depending on models.

The operating temperature range is 32°F (0°C) to 104°F (40°C) when used in High-Altitude mode (4,593 feet [1,400 m] to 8,858 feet [2,700 m]).

Also, if the ambient temperature exceeds 104°F (40°C) (95°F [35°C] in High-Altitude mode) when using all four lamps, the light output may be

reduced approximately 30% to protect the projector.

Dimensions

22-3/4" (578)

Throw distance

ET-D75LE3

3.0-5.0:1

max.

min.

max.

4,215 mm

4,226 mm

7,094 mm

13.8'

13.9'

23.2'

6,067 mm

6,077 mm

10,187 mm

19.9'

20.0'

33.4'

9,153 mm

9,164 mm

1,5341 mm

30.0'

20.2'

50.3'

12,240 mm

12,250 mm

20,496 mm

40.1'

40.2'

67.2'

18,413 mm

18,423 mm

30,805 mm

60.3'

60.5'

101.0'

24,586 mm

24,596 mm

41,114 mm

80.6'

80.7'

134.8'

36,932 mm

36,942 mm

61,732 mm

121.1'

121.2'

202.4'

4. If the projector is to be operated continuously 24 hours a day, use the multi-lamp optical system's alternating lamp operation (lamp changer)

function. The projector can be operated continuously 24 hours a day in four-lamp operation mode, but it will automatically operate with three

lamps for 8 hours of the 24 hours.

5. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.

• The length of time that it takes for the lamp to break or fail to illuminate varies greatly depending on individual lamp characteristics and usage

conditions.

• The brightness of the lamp will gradually decrease with use.

6. Because the ET-D75LE5 is a fixed short-throw lens, the lens shift function cannot be used with it.

7. Due to natural characteristics of lamps, screen brightness may vary (flicker). This is not an indication of faulty lamp performance.

For more information about Panasonic projector ––

Please contact Panasonic or your dealer for a demonstration.

Shape of the plug

unit: inch [mm]

receptacle

•125 V AC, 20 A

•250 V AC, 15 A

ET-D75LE4

ET-D75LE8

5.0-8.0:1

7.9-15.0:1

min.

max.

min.

7,101 mm

11,374 mm

11,091 mm

21,142 mm

23.3'

37.3'

36.4'

10,193 mm

16,292 mm

16,009 mm

30,358 mm

33.5'

53.4'

52.6'

1,5348 mm

24,488 mm

24,207 mm

45,717 mm

50.3'

80.3'

79.4'

20,502 mm

32,685 mm

32,404 mm

61,076 mm

67.3'

107.2'

106.3'

30,811 mm

49,078 mm

48,799 mm

91,794 mm

101.1'

160.9'

160.1'

41,120 mm

65,471 mm

65,194 mm

122,512 mm

134.9'

214.7'

213.9'

61,738 mm

98,257 mm

97,984 mm

183,948 mm

202.6'

322.2'

321.4'

http://panasonic.net/pavc/projector

EC98J2010

JQA-1617

Weights and dimensions shown are approximate. Specifications are subject to change without notice. This product

may be subject to export regulations. UHM is trademark of Matsushita Electric Indusutrial Co., Ltd. VGA and

XGA are trademarks of International Business Machines Corporation. All other trademarks are the property of their

respective trademark owners. Projection Images simulated.

DLP, DLP logo and DLP Medallion logo are trademarks or registered trademarks of Texas Instruments.

The PJLink trademark is an application trademark in Japan, the United States, and other

All information included here is valid as of July 2008.

ET-D75LE5

0.8:1

max.

fixed

1,022 mm

69.3'

3.3'

1,496 mm

99.5'

4.9'

2,286 mm

149.9'

7.5'

3,076 mm

200.3'

10.0'

4,656 mm

301.0'

15.2'

—

401.8'

—

603.3'

countries and regions or registered trademarks.

PT-D12KU1-08July10K Printed in Japan.