Panasonic PT-AE1000 Руководство по эксплуатации - Страница 22
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Проектор Panasonic PT-AE1000. Panasonic PT-AE1000 28 страниц. Panasonic lcd projector operating instructions
Также для Panasonic PT-AE1000: Руководство по эксплуатации (28 страниц)
Печатать страницу
Before replacing the Lamp unit
• ~ M w
awuuneu orr,
• Unplug all the cables from the projector.
• Prepare a Phillips-head screwdriver.
. Contact an Authorised Service Centre to purchase a replacement
Lamp unit
(ET-LAE1000).
note7~
~ *
'
—-——-—---
• Prior t0 replacing the lamp unit, allow it to cool down to prevent the risk nf h.,mo ^
* Do not attempt replacement with an unauthorised lamp unit.
'
396 and °ther haZardS-
When to replace the Lamp unit
2 000 hours is a rough guidance and might be shortened by the usage conditions chararterktirc nf h-, i
opTon^ucc'ndi,ions'and s° °n you can check *» *-«»
;™lrnrn"'
On screen
Indication
Over 1 800 hours
Over 2 000 hours
REPLACE LAMP
REPLACE LAMP" is displayed on the upper left of the
screen for 30 seconds.
To clear the screen immediately, press any button.
REPLACE LAMP" is displayed on the upper left of the
screen, and until you respond it will stay.
To clear the screen, press any button.
LAMP indicator
\\ 1
LAMP
Illuminates RED
NOTE;
~
—----—--—--_____
page aa9 ^ l3mP "fe' "*
LAMP P0WER in 0PTI0N menu to ECO - MODE See LAMP POWER" on
' pZZ7iTZ7aZpunT Un,P
SUCh 38 9U3M ,ime' see ,he "icemen. Instructions"
Replacing the lamp unit
■ upening the top cover
1 •
Turn off the MAIN POWER switch according to the
procedure "Switching the projector on/off' on
page 19 and disconnect the mains plug from the
mains socket.
•
Make sure the Lamp unit and the surroundings
are cooled enough.
2.
Open the top cover of the projector and remove
aside. See Back and bottom view" on page 13
*
Hold the toP c°ver up and press the buttons of
the both side of the hinge parts to remove.
/ "Press here
Press here
42 - English
1.
Use a Phillips screw driver to loosen the 3 lamp unit fixing
screws until the screws turn freely.
2.
Hold the handle of the lamp unit and release the lamp unit
lock.
3.
Pull out the lamp unit gently from the projector.
4.
Replace the new lamp unit while making sure that the
direction of insertion is correct.
•
Press the top of the lamp unit and make sure the unit is
installed securely.
5.
Tighten the lamp unit fixing screws securely with a Phillips
screwdriver.
H Attaching the top cover
1.
Attach the hinge parts of the top cover to the projector and press slightly
until it clicks
2.
Hook the tabs of the top cover to the projector and lift down slowly.
3.
Press the back corner of the top cover gently until it clicks.
NOTE:
• Be sure to install the lamp unit and the top cover of the projector securely. If they are
not securely installed, it may cause the protection circuit to operate so that the power
cannot be turned on.
• Grip the handle and keep the lamp unit paralleled when you remove the Lamp unit.
Some parts of the lamp unit are sharpened and may cause injury.
• Do not switch the power on while the top cover is opened.
■ Resetting the LAMP RUNTIME
If the lamp usage time has passed 2 000 hours (when LAMP POWER has been set to NORMAL), the projector will
switch to standby mode after approximately 10 minutes of operation. The resetting procedure should thus be
completed within 10 minutes.
1.
Connect the Mains lead to the projector and a
mains socket, and switch the MAIN POWER on.
2.
Switch the POWER button.
3.
Press the MENU button to display the menu.
4.
Press A V to select OPTION and press ENTER.
5.
Press A ▼ to select LAMP RUNTIME.
ALTITUDE
N
LAMP POWER
NORMAL
||
LAMP RUNTIME
1820H
FUNCTION BUTTON
6.
Press and hold the ENTER button for
approximately 3 seconds.
7.
The confirmation screen will be displayed and
select OK.
8.
Switch off the POWER to reset the duration of the
LAMP RUNTIME
9.
Confirm the duration of time in LAMP RUNTIME is
reset to "0".
English - a