Diamondback SE Руководство по установке - Страница 2

Просмотреть онлайн или скачать pdf Руководство по установке для Автомобильные аксессуары Diamondback SE. Diamondback SE 2 страницы. Hard tonneau cover for '15–up colorado & canyon with the 61.7" cargo box
Также для Diamondback SE: Руководство по установке (2 страниц), Руководство по установке (2 страниц), Руководство по установке (2 страниц), Руководство по установке (2 страниц)

Печатать страницу
Diamondback SE Руководство по установке
PREP FOR THE LOCK RODS
If a DiamondBack HD, unpin each of the four lock-rod guide-bracket slide plates
9
by using a 7/16" socket to move one of its bolts to the second, unoccupied slot.
If plastic extends beyond the bottom of the vertical face of the metal
10
bed rails, trim a two-inch length of it flush with the bed rail's bottom
edge at each of the four points where a lock rod will pass under the rails.
Peel the red adhesive backing from the edge trim pieces. Affix them
11
to the metal bed rail at the four points where a rod will pass under-
neath, the bottom curl of their j's touching the bottom edge of the rail.
Step 11 is unnecessary on '07–13 Silverados
and Sierras.
Affix the edge trim to the painted metal only, behind the plastic
bed liner or bed rail cap, if present.
You may need to pull the plastic bed rail cap away from the metal bed rail to
provide enough clearance to get the edge trim on.
Using a tool to widen the curl of the 'j' can
make this step easier.
ADJUST THE LOCK RODS
ADJUST THE LOCK RODS
Loosen the set screws on the
12
tailgate-panel lock-rod linkages.
Adjust the lock rods and retighten their set screws so that
13
A. with the lock handle in the open position, the rod tips clear
the bed rails,
B. with the handle in the closed position, the rod tips do not
strike the bed walls, and
C. the first bend in the rods points downward.
ATTACH THE SAFETY CATCH & GAS SPRINGS
ADJUST THE LOCK RODS
Fit the safety catch, which is hanging
16
from the driver side of the cab panel,
around the bottom ball stud.
Attach a gas spring to the ball studs
17
alongside the safety catch.
If some of your gas springs have
heavier poundage printed on their
sides than others, use the stron-
ger ones on the cab panel.
To avoid premature
failure of your gas
springs, attach them
barrel up, shaft down.
DiamondBackCovers.com
1/8" hex key
Position the lock rods tight
14
against the underside of
the bed rails so that they'll
draw the panels down and
compress the weather-
strip. Tighten the rod guide
brackets with a 7/16"
socket.
For best weather protection, have a second person
press down on the cover while you adjust the lock rods.
Using the access panels is easiest when
you press down as you open or close them.
Repeat steps 12 through 14 for the cab panel.
15
Your panels should be hard to operate at first. After finishing
install below, leave the panels closed as much as possible for
3–4 days to break in the weatherstrip. After that period, you
should find that the panels open and close without difficulty.
If you are also installing a Cross Bin, do so now. Refer
to the Cross Bin Installation Guide for details.
Attach the three remaining gas springs
18
(barrel up, shaft down).
If your truck has bed rail caps, affix the included
19
bulkhead weatherstrip. Refer to the Bulkhead
Prep Kit Installation Guide for details.
Leave the cover closed and locked for 24
20
hours to allow the weatherstrip adhesive,
which is pressure-sensitive, to fully cure.
7/16" socket
24 hours
Adhesive cure time
SEPTEMBER 2018