Panasonic SA-AK770 Руководство по эксплуатации - Страница 12
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Стереосистема Panasonic SA-AK770. Panasonic SA-AK770 24 страницы. Panasonic cd stereo system operating instructions
Печатать страницу
Cassette tape – Play and record
The buttons described for "Cassette tape – Play and record"
are mainly using the main unit unless indicated otherwise.
Use normal position tapes.
High position and metal position tapes can be played, but the unit
will not be able to identify the characteristics of these tapes.
1
Press [3, TAPE].
The unit turns on.
If a cassette was loaded, play starts automatically (One touch
play).
2
Press [0, OPEN] and insert the cassette.
Insert with the side to be played facing towards you and the
exposed tape facing down. Close the holder by hand.
3
Press [3, TAPE] to start play.
To
Stop tape playback
Fast-forward and
rewind
Note:
• Tapes exceeding 100 minutes are thin and can break or get
caught in the mechanism.
• Tape slack can get caught up in the mechanism and should be
wound up before the tape is played.
TPS (Tape Program Sensor)
This function enables you to search the beginning of up to a
maximum of 9 tracks.
Press [ / REW / 4] or [ / FF / ¢] during play.
Play resumes from the track found.
Note:
TPS may not operate correctly in the following situations:
• If the interval between tracks is less than 4 seconds.
• If there is noise between tracks.
• If there are silent parts within tracks.
Recording
Recording
Selection of tapes for recording
Use normal position tapes.
High position and metal position tapes can be used, but this unit
will not be able to record or erase them correctly.
Note:
• Changes to volume and sound quality do not affect recording.
• This function does not work during any "RANDOM" mode
selection.
Preparation
Wind up the source tape so recording can begin immediately.
1
Press [0, OPEN] and insert the cassette to be recorded.
Insert with the side to be recorded facing towards you and the
exposed tape facing down.
12
RQT8043
Basic play
Basic play
Action
Press [-7 STOP, –DEMO].
Press [ / REW / 4] or [ / FF / ¢ ] in the
stop mode.
2
Select the source to be recorded.
Radio recording:
Tune in the station. (\ page 13)
Disc recording:
➀
Insert the disc(s) you want to record.
Press [6, CD] and then [-7 STOP, –DEMO].
➁
Prepare the desired disc recording mode.
To
Action
Record
programmed
Perform steps 2 to 4 in "Program play"
tracks
(\ page 11).
Perform steps 3 to 6 in "Program play"
(\ page 11).
By remote control only
Record
1) Press [DISC] and then [1] ~ [5] to select
specifi c discs
the disc.
or tracks
Ensure disc is stopped.
2) Press [PLAY MODE] to select the desired
mode (\ page 10).
3)
For 1-ALBUM mode and 1-TRACK mode:
Press [5/∞, ALBUM] to select the album.
For 1-TRACK mode:
Press [4,
select the track.
3
Press [¶ REC, TAPE] to start recording.
Other basic operations
To
Action
Stop recording
Press [-7 STOP, –DEMO].
Record on the other
Turn the cassette over and press
side of the tape
[¶ REC, TAPE].
Erase a recorded
1) Press [3, TAPE] and then
sound
[-7 STOP, –DEMO].
2) Insert the recorded cassette.
3) Press [¶ REC, TAPE].
Your attention is drawn to the fact that recording pre-recorded
tapes or discs or other published or broadcast material may
infringe copyright laws.
Erasure prevention
The illustration shows how to remove the tabs to prevent recording.
To record on the tape again, cover as shown.
Side A
Tab for side B
Tab for side A
To re-record
Normal cassette
Adhesive tape
/ REW] or [¢,
/ FF] to