Bionaire BCH160 Руководство по эксплуатации - Страница 2

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Нагреватель Bionaire BCH160. Bionaire BCH160 2 страницы. 1.8 kw compact ceramic heater

Печатать страницу

BCH160

Fig.1

BCH160

Fig.2

BCH160-IUK_10EM1.indd 5-8

U.K. and IRELAND

11. Allow a safe area around the heater away

from furniture or other objects; at least 50

cm from the top and sides and 200 cm at the

front.

RETAIN THE FOLLOWING FOR FUTURE

12. Do not use this heater when it is lying on its

REFERENCE.

side.

DESCRIPTIONS (See Fig.1 & 2)

13. DO NOT use the heater in rooms with

A. Front Housing

explosive gas (e.g. petrol) or while using

B. Back Housing

inﬂ ammable glue or solvent (e.g. when gluing

or varnishing parquet ﬂ oors, PVC etc).

C. Grill

14. DO NOT insert any objects into the heater.

D. Power Light Ring

15. Keep the mains cord at a safe distance from

E. Mode Control

the main body of the heater.

F. Thermostat Control

16. If overheating should occur, the built-in

PLEASE READ AND SAVE THESE

overheating safety device will switch off the

IMPORTANT INSTRUCTIONS

heater.

When using electrical appliances, basic safety

17. Do not place the cord under a rug.

precautions should always be taken including the

18. The heater cannot be used adjacent to

following:

curtains or combustible material. Curtains or

1. Before connecting the heater, check that

combustible material may be burned if the

the voltage indicated on the rating plate

heater was installed incorrectly.

corresponds to the main voltage in your

19. This appliance is not intended for use by

home/ofﬁ ce.

persons (including children) with reduced

2. WARNING: In order to avoid overheating,

physical, sensory or mental capabilities,

do not cover the heater (

or lack of experience and knowledge,

unless they have been given supervision or

3. DO NOT position the heater directly under a

instruction concerning use of the appliance

power socket.

by a person responsible for their safety.

4. Do not use this heater in the immediate

Children should be supervised to ensure that

surroundings of a bath, a shower or a

they do not play with the appliance.

swimming pool.

20. WARNING: Risk of Fire. Discontinue

5. If the supply cord or plug is damaged, it must

use if the outlet or plug become hot to the

be replaced by the manufacturer or its service

touch. Overheating may indicate a worn

agent or similarly qualiﬁ ed person in order to

or damaged outlet. Consult a qualiﬁ ed

avoid hazard. The heater contains no user

electrician for outlet replacement.

serviceable parts. Should the product suffer

21. CAUTION: In order to avoid a hazard due

damage or breakdown, it must be returned to

to inadvertent resetting of the thermal cutout,

the manufacturer or their service agent.

this appliance must not be supplied through

6. Under the environment with electrical fast

an external switching device, such as a timer,

transient, the product may malfunction and

or connected to a circuit that is regularly

require user to reset the product.

switched on and off by the utility.

7. Do not use this heater with a programmer,

timer or any other device that switches the

heater on automatically, since a ﬁ re risk

exists if the heater is covered or positioned

incorrectly.

8. Only touch the heater with dry hands.

9. DO NOT use this heater outdoors.

10. DO NOT position where it can be touched by

children, especially the very young.

OPERATING INSTRUCTIONS

AUTO SAFETY SHUT OFF

1. Make sure the unit is in the OFF (O) position

This heater is equipped with a technologically-

before plugging the heater into the wall

advanced safety system that requires the user

socket/outlet.

to reset the heater if there is a potential overheat

situation. When a potential overheat temperature

2. Place heater on a ﬁ rm level surface. Once

is reached, the system will automatically shut the

plugged in, the power light ring (D) will

heater off. It can only resume operation when the

remain lit during operation.

user resets the unit. If the heater shuts off, please

3. Avoid overloading your circuit by not using

follow the speciﬁ c reset instructions below:

other high wattage appliances in the same

1. Turn Mode Control to OFF (O) position and

outlet. At 1800 Watts, this unit draws 8.2

the Thermostat Control to the fully anti-

Amps.

clockwise position.

Mode Control

2. Unplug unit from socket and wait 30 minutes

Turn the Mode Control (E) to the desired setting:

for the unit to cool down.

O - Off Mode

3. After the 30 minutes, plug the unit in and

operate normally.

If you want to shut off the heater at any time

of operation, turn the mode button to OFF (O)

CLEANING AND MAINTENANCE

position. The power light ring will remain lit until

•

Turn off the unit.

the heater is turned to OFF (O).

•

Remove the plug from the wall socket.

- Fan only Setting

•

Wait for the heater to cool down sufﬁ ciently.

The heater will run at Fan-only operation without

•

You may clean the outside of the heater with

any heat output.

a damp cloth. DO NOT allow water to come

1- LOW Heat

into the appliance. DO NOT use soap or

The heater will run continuously at 1200W.

chemicals, which may damage the housing.

Allow sufﬁ cient time to dry before plugging

2- HIGH Heat

the unit back in the socket.

The heater will run continuously at 1800W.

•

Clean the air inlet and outlet openings

NOTE: To start the heater operation, make sure

regularly (with normal use at least twice a

the Thermostat Control (F) is turned to the full

year) with a vacuum cleaner.

clockwise position.

- Thermostat Control

1. Before setting the thermostat, allow heater

to operate and warm up the room. As noted

above, you need to turn the Thermostat

Control (F) to the full clockwise position to

start the heater.

2. When the desired temperature/ comfort level

is reached, lower the thermostat setting

until the heater stops operating. This is

done by moving the Thermostat control (F)

anticlockwise toward the Frost Guard setting

(

). If moved to the Frost Guard (

) the

thermostat is set to 5°C, the heater will turn

on automatically if the temperature goes

below 5°C so as to avoid a frost situation.

3. The control will now automatically maintain

the pre-set temperature level by turning the

heater ON and OFF.

NOTE: It is normal for the heater to cycle ON

and OFF as it maintains the preset temperature.

To prevent the unit from cycling , you need to

change the thermostat setting.

CAUTION: THE GRILL (C) IS HOT WHEN

UNIT IS IN OPERATION.

FOR U.K. AND IRELAND ONLY

If the plug is not suitable for the socket outlets

in your home, it can be removed and replaced

by a plug of the correct type. Please refer to

"Installation of a plug" below.

Installation of a plug applicable to U.K.

and Ireland only

NOTE: If the terminals in the plug are not

marked or if you are unsure or in doubt about the

installation of the plug please contact a qualiﬁ ed

electrician.

If a 13A 3-pin plug is ﬁ tted, it must be an ASTA

approved plug, conforming to BS1363 standard.

Replacement 13A fuses must be BSI or ASTA

BS1362 approved.

This product is ﬁ tted with a 13A plug complying to

BS1363. If this plug is unsuitable or needs to be

replaced, please note the following: The wires in

the mains lead are coloured as such:

BROWN -

LIVE

BLUE

NEUTRAL

Please note that the colour of these mains wires

may not correspond with the colour markings

that identify the terminals in your plug. Please

proceed as follows:

The BROWN coloured wire must be connected to

the terminal, which is marked with the letter "L" or

is coloured RED.

The BLUE coloured wire must be connected to

the terminal, which is marked with the letter "N"

or is coloured BLACK.

DO NOT CONNECT either of these wires to the

earth terminal in the plug. The earth terminal plug

is marked with the letter "E", or with the earth

symbol

, or coloured GREEN, or GREEN and

YELLOW.

3/4/10 9:46:57 AM