Axon Body 2 Краткое руководство по эксплуатации - Страница 2
Просмотреть онлайн или скачать pdf Краткое руководство по эксплуатации для Камера безопасности Axon Body 2. Axon Body 2 2 страницы.
Также для Axon Body 2: Краткое руководство по эксплуатации (2 страниц), Краткое руководство по эксплуатации (2 страниц), Руководство по быстрым советам (6 страниц)
Печатать страницу
Status LED
When you plug your camera into the Axon Dock, the Axon Body 2
camera status LED displays the camera's status.
Device Status
Initial connection (momentary)
In queue awaiting upload
Device ready (all videos uploaded successfully)
Device not assigned, agency mismatch, camera
set in the offline mode, or device error
Uploading data
Firmware update, internal battery charging,
extremely low battery, or memory full
Transfer error, device re-trying to transfer
Possible network error. Verify Axon Dock is
registered and refer to the Troubleshooting
chapter of the User Manual or go to
help.axon.com.
Axon Dock has no communication with the
camera. Verify the Axon Dock core and bays
are seated properly. Contact Axon Technical
Support if not resolved.
Notifications
The Axon Body 2 camera emits beeping sounds called audio prompts to notify you of the system status. These audio prompts usually occur after
you perform an action with the camera. The audio prompts are accompanied by vibrations that match the beeps.
Powering on or off
Recording an event
The device is ending an event and returning to BUFFERING mode
Low battery notifications:
•
Camera in BUFFERING mode and battery has power for 20 minutes or less
•
Camera in EVENT (recording) mode and battery nearly discharged (the
camera will shut down within a few minutes)
Camera memory is full (the camera will not record)
Camera internal clock is not set OR Error state*
*When the Operation and Function LEDs are also solid red.
Using Axon View
The Axon View application enables you to replay
video and add metadata (GPS, title, case ID, and
category) to your videos using a smart phone or other
smart device.
1. Using your smart device, search for and download
the Axon View application from the Play Store or
the App Store.
2. On your smart device, install and open the Axon
View application
3. F ollow the onscreen ins tr uc tions or go to
help.axon.com
for addiitonal information.
Note: All data is stored on the Axon camera. No videos are stored
on your smart device.
Bluetooth is a trademark of the Bluetooth SIG, Inc.; Play Store is a trademark of Google, Inc.;App Store is a trademark of Apple, Inc.; iOS is a trademark of Cisco Systems,
Inc.; and Windows is a trademark of Microsoft Corporation.
, AXON, Axon, Axon Body 2, Axon Dock, Axon View, and Evidence Sync are trademarks of Axon Enterprise, Inc., some of which are registered in the US and other
countries. For more information, visit www.axon.com/legal. All rights reserved. © 2019 Axon Enterprise, Inc.
Status LED
Solid red (for 20 seconds or
fewer)
Solid yellow
Solid green
Blinking red
Blinking yellow
Blinking red and yellow – DO
NOT remove the camera
from the Axon Dock
Blinking green and yellow
Blinking red, yellow, and then
green (cycling all colors)
LED off
Operating Mode
Recharging the Battery and Uploading Data
The Axon Dock is used to recharge the Axon Body 2 camera's battery
and upload data. If you do not have an Axon Dock, upload video
with a Windows compatible computer using Evidence Sync. For more
information about Evidence Sync, go to help.axon.com.
1. Ensure the Axon Body 2 camera is off.
2. Insert the camera into the Axon Dock with
the power switch down, as shown in the
image to t h e r ig h t . T h e A xon D o c k
automatically:
• Uploads data
• Deletes videos from the camera
• Updates camera firmware and settings
• Charges the camera battery
3. It is recommended that you wait until the
battery LED displays green before
removing the camera from the Axon
Dock.
DO NOT remove the camera if the status LED is blinking red
and yellow.
Audio Notification
One beep
Two beeps (every 2 minutes)
One long beep
Four quick beeps (every 20 seconds)
Three beeps
Five quick beeps (every 20 seconds )
Pairing an Axon Body 2 Camera with Axon View
1. Turn on the Axon Body 2 camera and wait until the camera boots
up.
2. Open Axon View, select a Body 2 camera and tap Initiate Pairing.
3. Hold down the Function and EVENT buttons for 5 seconds.
4. Wait until you hear four beeps. The Function LED will blink green.
5. On your smart device, follow the onscreen instructions.
MPC0205 Rev: H
Haptic Notification (Vibration)
Once
Twice (every 2 minutes)
Once, long duration
Four times, quickly (every 20 seconds)
Three times
Five times, quickly (every 20 seconds)