ARC Audio X2 1200.6 Руководство пользователя - Страница 7
Просмотреть онлайн или скачать pdf Руководство пользователя для Усилитель ARC Audio X2 1200.6. ARC Audio X2 1200.6 13 страниц. Full-range class d amplifier
Печатать страницу
Fuses
The X2 1200.6 includes three 30 amp ATC/ATO fuses on the
left side of the end-panel. These fuses exist to protect the
internal circuitry of the amplifier from damage and are not a
replacement for a proper fuse at the battery in your vehicle.
Under no conditions should you increase the value of the
fuses used in this location.
If the fuses blow immediately upon insertion, contact your
authorized ARC Audio dealer or the Technical Support
department at ARC Audio for assistance.
CH3/4
HP RANGE
Auto Sense Turn-On Detection
GAIN
110
MIN
The X2 1200.6 features two Auto-Sense Turn-On modes. In
FULL
X1
HIGH
DC Detect mode, the amplifier monitors the Channel 1 RCA
X10
MAX
330
input for the presence of a DC offset voltage (common with
BANDPASS
LP RANGE
Bridge Tied Load (BTL) source units and amplifiers). When
110
110
50
this DC voltage is present, the amp will turn itself on.
OFF
X1
ON
X10
500
330
330
When set to Signal Detect, the X2 1100.5 monitors the
LOWPASS
FREQ Hz
CH1/2
Channel 1 RCA input for the presence of an audio signal.
When an audio signal is present, the amp will turn itself on.
The amp automatically turns off 10 seconds after the DC
Detect or Signal Detect no longer sees an appropriate signal.
When using either Auto-Detect mode, only the Channel 1 input is monitored.
The Turn On input on the power terminal block is NOT used when Auto Detect is turned on.
Remote Level Control
The X2 1200.6 ships with a remote level control that can be
TURN ON
installed in near the driver's seat so the owner can adjust the
+12V
GND
level of a subwoofer. The Level control only affects the output
of channels 5 and 6.
To set the gains on this amplifier, either leave the Remote
Level Control disconnected or turn it to it's maximum setting
(fully clockwise). The Remote Level Control functions as an
attenuator so as not to alter the gain structure of the amp and
cause distortion, unlike a remote bass boost control.
Accessing Controls and Mounting Provisions
The X2 1200.6 features our Level 2 X2-Series cosmetics.
The amplifier shroud features an elegant new silver brushed-
aluminum extruded aluminum design. An acrylic plastic badge
in the center of the amp illuminates in blue when the amp is
on, and can flash diagnostic codes as required. The badge
may be rotate in 90 degree increments to suit any installation.
To access the controls on the top of the amp, remove the four
screws in the badge and set them in a safe place. Remove the
badge and set it in a safe place. The amp shroud can now be
removed for tuning and installation.
Note: Amplifier shown represents X2-Series amplifier.
Dimensions are not to scale.
4CH STEREO
BRIDGED 2CH
(
)
FRONT
LOW
FULL
GAIN
MIN
HIGH
MAX
2 CH INPUT
CH1
CH3
CH2
CH4
BRIDGED
INPUT
CH5
+12V
CH6
FUSE 30 AMP X 3
FUSE 30 AMP X 3
INPUT
SELECT
CH1/2
dB
INPUT
CH5/6
12
SELECT
HIGHPASS
HP RANGE
FREQ Hz
110
50
CH1
2CH
4CH
500
330
AUTO
BANDPASS
SENSE
110
50
SIGNAL
OFF
REMOTE
DETECT
ON
OFF
LEVEL
500
DC DETECT
330
4
Ω
BRIDGED
HIGHPASS
USE UNDER 4Ω
FREQ Hz
BASS
INPUT
BOOST
SELECT
0
2 CH INPUT
CH1/2
dB
TURN ON
CH5/6
CH1
12
GND
CH1
REMOTE
LEVEL
4
Ω
BRIDGED
CH2
USE UNDER 4Ω
BRIDGED
INPUT
TURN ON
+12V
GND
BASS
HIGHPASS
LO
BOOST
BAND
110
50
50
PASS
0
OFF
CH3/4
ON
500
500
330
GAIN
MIN
CH2
CH3
FULL
X1
HIGH
CH1/2
X10
LOAD
MAX
SELECT
LP RANGE
LO
UNDER
Ω
110
4
50
X1
OVER
X10
Ω
500
4
330
4
Ω
B
LOWPASS
2Ω MIN
USE U
FREQ Hz
CH1/2
LOWP
HIGHPASS
BAND
110
50
50
PASS
OFF
CH3
ON
CH5
500
500
330
CH2
CH3
CH1/2
LOAD
SELECT
UNDER
Ω
4
OVER
Ω
4
4
Ω
BRID
CH4
2Ω MIN
CH6
USE UNDE
Page 7