ABB ACS550 Series Краткое руководство по эксплуатации

Просмотреть онлайн или скачать pdf Краткое руководство по эксплуатации для Контроллер ABB ACS550 Series. ABB ACS550 Series 2 страницы. Drive it low voltage ac drives 150...550 hp
Также для ABB ACS550 Series: Краткое руководство по эксплуатации (2 страниц), Руководство пользователя (14 страниц), Дополнительное руководство по установке (16 страниц)

Печатать страницу

ACS550

Quick Start Guide

ACS550-01 Drives (0.75...160 kW),

IP54 / UL Type 12 Enclosure

Overview

The installation of the ACS550 adjustable

speed AC drive follows the outline below.

PREPARE for installation

PREPARE mounting location

REMOVE the front cover

MOUNT the drive

INSTALL wiring

CHECK installation

REINSTALL the cover

APPLY power

START-UP

Application

This guide provides a quick reference for

installations involving: ACS550-01 drives, cable

connections and IP54 / UL type 12 enclosures.

Note: This guide does not provide detailed

installation, safety or operational

instructions. See ACS550 User's Manual for

complete information.

Prepare for installation

WARNING! The ACS550 should ONLY be

installed by a qualified electrician.

Unpack the drive

Note: Lift the ACS550 by its chassis and not by its

cover.

1. Unpack the drive.

2. Check for any damage.

3. Check the contents against the order / shipping

label.

Check

• Motor compatibility – Motor type, nominal

current, frequency and voltage range must

match drive specifications.

• Suitable environment – Drive requires heated,

indoor controlled environment that is suitable

for the selected enclosure.

• Wiring – Follow local codes for wiring, circuit

protection and EMC requirements.

Refer to User's Manual and confirm that all

preparations are complete.

Drive identification

ACS550-01-08A8-4

3~ 380...480 V

I2N/ I2hd 8.8/6.9 A

Serno

*2030700001*

PN/Phd

4.0/3.0 kW

Use the following chart to interpret the type

code found on the drive label.

ACS550-01-08A8-4+B055+...

AC, Standard Drive – 550 series

Construction (region specific)

01 = Setup/parts for IEC install./compliance

U1 = Setup/parts for US install./compliance

Output current rating

See Ratings in User's Manual for details

Voltage rating

2 = 208...240 V AC

4 = 380...480 V AC

6 = 500...600 V AC

Options

Examples of options:

No specification = IP21 / UL type 1

B055 = IP54 / UL type 12

UL type 12 is not available for type

ACS550-01-290A-4.

0J400 = No control panel

J404 = ACS-CP-C Basic Control Panel

Collect motor data

Collect the following data from the motor

nameplate for later use in the ACS550 startup:

• Voltage __________________________

• Nominal motor current ______________

• Nominal frequency _________________

• Nominal speed ____________________

• Nominal power ____________________

Tools required

Screwdrivers, wire stripper, tape measure,

mounting screws or bolts and drill.

Prepare the mounting location

The drive requires a

smooth, vertical, solid

surface, free from heat and

moisture, with free space for

air flow – 200 mm (8 in)

above and below.

1. Mark the mounting points

using the template.

2. Drill the mounting holes.

X0002

Remove the front cover

1. If hood is

present:

Remove screws

(2) holding hood

in place.

2. If hood is

present: Slide

hood up and off

the cover.

3. Loosen the

captive screws

around the edge

of the cover.

4. Remove the

cover.

Mount the drive

The holes providing for access to the drive

mounting slots require rubber plugs.

1. As required for access,

remove the rubber

plugs. Push plugs out

from the back of the

drive.

2. R5 & R6: Align the

1, 4

sheet metal hood (not

shown) in front of the

drive's top mounting

holes. (Attach as part of

next step.)

3. Position the ACS550 and securely tighten in all

four corners.

Note: Lift the ACS550 by its metal chassis.

4. Reinstall the rubber plugs.

5. Non-English speaking locations: Attach a

warning sticker in the appropriate language

over the existing warning on the top of the

module.

Install the wiring

General wiring

1. Cut the rubber cable

seals as needed for the

power, motor and control

cables. The conical part

of the seals must face

downwards when

inserted in the lead-

through plate holes.

Wiring power

1. On the input power

cable, strip the

sheathing back far

enough to route

individual wires.

2. On the motor cable,

strip the sheathing

back far enough to

expose the copper wire shield so that the shield

can be twisted into a bundle. Keep the bundle

bundle not longer than five times its width to

minimize noise radiation. – 360° grounding

under the clamp is recommended for the motor

cable to minimize noise radiation. In this case,

remove the sheathing at the cable clamp.

3. Route both cables through the clamps and

tighten the clamps.

4. Connect the bundle created from the motor

cable shield to the GND terminal.

5. Strip and connect the power/motor wires and

the power ground wire to the drive terminals

using the torques given in the table below. See

Power connections

below or, for more detail,

see User's Manual.

Frame size

Tightening torque

N·m

R1, R2

1.4

2.5

5.6; PE: 2

40; PE: 8

IP5003

IP5004

lb·ft

1.8

4; PE 1.5

30; PE: 6