Axxess AX-AU12-SWC Руководство по установке - Страница 7
Просмотреть онлайн или скачать pdf Руководство по установке для Автомобильные аксессуары Axxess AX-AU12-SWC. Axxess AX-AU12-SWC 12 страниц. Data interface with swc for audi
Печатать страницу
L.E.D. feedback
The (18) Red L.E.D. flashes represent what brand radio the AX-AU12-SWC believes it is
connected to. Each flash represents a different radio manufacturer. For example, if you
are installing a JVC radio, the AX-AU12-SWC will flash (5) times. Following is a legend that
dictates which manufacturer corresponds to which flash.
L.E.D. feedback legend
1 flash - Eclipse (Type 1) †
2 flashes - Kenwood ‡
3 flashes - Clarion (Type 1) †
4 flashes - Sony / Dual
5 flashes - JVC
6 flashes - Pioneer / Jensen
7 flashes - Alpine *
8 flashes - Visteon
9 flashes - Valor
* Note: If the AX-AU12-SWC flashes Red (7) times, and you do not have an Alpine radio
connected to it, that means the AX-AU12-SWC does not detect a radio connected it. Verify
that the 3.5mm jack is connected to the correct steering wheel jack/wire in the radio.
** Note: Part number AX-SWC-PARROT is required (sold separately). Also, the Parrot radio
must be updated to rev. 2.1.4 or higher through www.parrot.com.
† Note: If you have a Clarion radio and the steering wheel controls do not work, change the radio
type to the other Clarion radio type; same for Eclipse. The following section explains how to do this.
‡ Note: If you have a Kenwood radio and the L.E.D. feedback comes back as showing as a JVC
radio, change the radio type to a Kenwood. The following section explains how to do this.
STEERING WHEEL CONTROL SETTINGS
10 flashes - Clarion (Type 2) †
11 flashes - Metra OE
12 flashes - Eclipse (Type 2) †
13 flashes - LG
14 flashes - Parrot **
15 flashes - XITE
16 flashes - Philips
17 flashes - TBD
18 flashes - JBL
Attention: The Axxess Updater App can also be used to program the following (3) sub-sections as
well, pending that the interface has been initialized and programmed.
Changing radio type
If the LED flashes do not match the radio you have connected, you must manually program
the AX-AU12-SWC to tell it what radio it is connected to.
1. After (3) seconds of turning the key on, press and hold the Volume-Down button on the
steering wheel until the L.E.D. in the AX-AU12-SWC goes solid.
2. Release the Volume-Down button; the L.E.D. will go out indicating we are now in Changing
Radio Type mode.
3. Refer to the Radio Legend (next page) to know which radio number you would like to have
programmed.
4. Press and hold the Volume-Up button until the L.E.D. goes solid, and then release. Repeat
this step for the desired radio number you have selected.
5. Once the desired radio number has been selected, press and hold the Volume-Down button
on the steering wheel until the L.E.D. goes solid. The L.E.D. will remain on for about (3)
seconds while it stores the new radio information.
6. Once the L.E.D. goes off, the Changing Radio Type mode will then end. You can now test the
steering control wheel controls.
Note: If at any time the user fails to press any button for a period longer than (10)
seconds, this process will abort.
Continued on the next page
REV. 7/19/2018 INSTAX-AU12-SWC
7