Epson 1280 - Stylus Photo Color Inkjet Printer Руководство по установке - Страница 5

Просмотреть онлайн или скачать pdf Руководство по установке для Принтер Epson 1280 - Stylus Photo Color Inkjet Printer. Epson 1280 - Stylus Photo Color Inkjet Printer 8 страниц. Product support bulletin(s)
Также для Epson 1280 - Stylus Photo Color Inkjet Printer: Замена картриджей (2 страниц), Бюллетень поддержки продуктов (6 страниц), Бюллетень поддержки продуктов (1 страниц), Дополнительное руководство (1 страниц), Руководство пользователя (27 страниц), Руководство по совместимости (1 страниц), Дополнительное руководство (2 страниц), Начните здесь (2 страниц), Брошюра и технические характеристики (2 страниц), Информация о продукте (13 страниц), Начните здесь Руководство (6 страниц), Технические характеристики (2 страниц), Руководство пользователя (12 страниц), Бюллетень поддержки продуктов (3 страниц), Бюллетень поддержки продуктов (2 страниц), Бюллетень поддержки продуктов (4 страниц), Бюллетень поддержки продуктов (7 страниц), Руководство по началу работы (32 страниц)

Печатать страницу
Epson 1280 - Stylus Photo Color Inkjet Printer Руководство по установке
6. Clean the right section of the printer housing with alcohol, then install the second
bracket on the right hand edge of the housing so the tubing is in a straight line. Put
the tubing into this small bracket. Now you are ready to insert the tubes into the
bottles. The position of the bracket opening can be either up or down. It does not
matter.
7. Next, you must install the Tube Guide onto the cartridge carriage. The Tube Guide
is installed on the side of the carriage that has the black cartridge. Clean the area
where the tube guide is to be installed with a small amount of alcohol. The bracket
is installed in such a way that the edge of the bracket is 1/8 of an inch from the
black cartridge on the left side and front. The Tube Guide position should be as
shown in the picture below.
After installation, check to be sure that the Tube Guide does not hit the left hand
side of the printer housing when the carriage is all of the way to the left side of
the printer. Since this dimension is very close it is best to check this by sliding a
business card between the Tube Guide and the printer housing with the carriage
moved all of the way to the left. If the business card slides freely between the
tube guide and the printer housing, it is installed correctly.
Set up the Bottles and Connect the Tubes:
The Spongeless CFS System that you have been shipped contains a set of our new bottle
caps with fittings. It also has white plugs on the tube ends that were not there before.
The installation of the tubes is as follows.
8. Once the tubes have the slack adjusted properly and they are securely inserted
into the Bridge Bracket clip, let the remaining tube length feed thru the beige clip
on the right hand edge of the printer. Close the clamp on the tubing. This will leave
the remaining tube length at the right side of the printer ready to be trimmed for
connection to the bottle tops.
S a v e
M o n e y
MIS Associates Inc
http://www.inksupply.com
a n d
I m p r o v e
2901 Auburn Rd
Fax: 248-289-6013
Y o u r
Auburn Hills, MI 48326
P r i n t i n g
800-445-8296