CREE LIGHTING Stylus ST3-WD Руководство по установке - Страница 7

Просмотреть онлайн или скачать pdf Руководство по установке для Фонарь CREE LIGHTING Stylus ST3-WD. CREE LIGHTING Stylus ST3-WD 7 страниц. Led ambient luminaire, wall mount

Печатать страницу

End Plate Cap

(With Alignment

Female Joiner Bracket

Pins)

End-Plate

Lock Nuts

FCC NOTICE

CAUTION: Changes or modifications not expressly approved could void your authority to use this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense. CAN ICES-005 (A)/NMB-005 (A)

SECTION 8:

ELECTRICAL CONNECTIONS

STEP 1:

For 120/277/347V applications make the following Electrical Connections:

a. Connect the black luminaire lead to the supply lead.

b. Connect the white luminaire lead to the neutral supply lead.

c. Connect the green or green/yellow ground lead to the green

supply lead.

For 208/240V applications, make the following Electrical Connections:

a. Connect Hot 1 supply lead to the black lead.

b. Connect Hot 2 supply lead to the white lead

c. Connect the green or green/yellow ground lead to the supply

ground lead.

STEP 2:

a. If applicable, the dual feed option comes with the indirect switched

Hot connected to the red luminaire lead. Connect the red luminaire

lead to indirect switched Hot supply lead. If not being used, ensure

to cap off red leads.

b. If Dimming is an option; connect the violet dimming positive lead

to the supply dimming positive lead. If dimming is not being used,

ensure to cap off the violet lead. For dual feed indirect positive

dimming lead is blue.

c. If Dimming is an option; connect the grey dimming negative lead

to the supply dimming negative lead. If dimming is not being used,

ensure to cap off the grey lead. For dual feed indirect negative

dimming lead is blue/white.

is subject to change. See www.creelighting.com/warranty for warranty and specifications. Cree

registered trademarks of Cree, Inc.

7 of 7

STEP 10:

Locate and install End Cap Kits:

• Attach the end cap to the male end of the first luminaire by removing the

• On the last luminaire in the run attach the endcap to the female end of the

STEP 11:

Once all luminaires in a row are installed, tighten Wall Cleat screws on all

Slide Screw

luminaires enough to hold luminaires snug to the wall.

w/ Lock Nuts

STEP 12:

Replace LED trays and lens that was removed in Step 4 above, ensure that no

wires are pinched.

NOTE: For ST3-WI luminaires lens must be reinstalled with shiny side facing the

LEDs for proper light distribution.

and the Cree logo are

male joiner bracket by loosening the 2 keps nuts inside the luminaire

and install the female joiner bracket using 2 keps locknuts and endcap

(provided in the end cap kit) onto the end of the luminaire. See Figure 12.

luminaire. Secure the endcap to the luminaire's female joiner bracket from

the inside of the housing with 2 provided keps locknuts.

LINE OR HOT 1

GREEN

NEUTRAL OR HOT 2

INDIRECT SWITCHED

DIM (+) VIOLET

DIM (-) GREY

DIM (+) VIOLET

DIM (-) GREY

Reserved for Dual Feed Indirect

LUMINAIRE

LINE-BLACK

GROUND-GREEN

NEUTRAL-WHITE

INDIRECT SWITCHED

-RED

VIOLET

GREY

BLUE

BLUE W/WHITE

www.creelighting.com

LPN00644X0008A0_A