Accusplit Eagle AE120XLG Инструкция по эксплуатации - Страница 3
Просмотреть онлайн или скачать pdf Инструкция по эксплуатации для Шагомер Accusplit Eagle AE120XLG. Accusplit Eagle AE120XLG 4 страницы. Accusplit pedometer operating instructions
Печатать страницу
First, loop leash
through slot on side
of pedomete
r
Next, clasp clothing
Or, loop a belt
or belt loop
16
GOAL TRACKING
As discussed in beginning of instructions, this unit keeps
track of your progress towards the Step and T ime goals you
set. Progress is shown as a series of small bars appearing
on the bottom of the display, with each bar representing
5% of the total. For example, if you set your step goal to
4,000 steps, and you've walked 2,000 steps so far, the goal
indicator in STEP mode will show as 50% complete. Progress
towards each goal is shown on the corresponding screen
– for example, when viewing T IME, you will see both the time
traveled in hours and minutes, and also the progress towards
your time goal on the bottom of the display.
18
CHANGING STEP FILTER SETTING
While the JW200 PedometerEngine™ Step Sensor is
extremely accurate, some people like to have the ability to
filter out false steps. T herefore, the unit has a variable setting
step filter, to allow fine-tuning to your specific preferences.
You can set the value to any value from 0 – 5 steps. For
example, if the filter is set to "3" , the unit will wait to start
counting steps until more than three steps have been taken in
less than five seconds.
Press S3+ (MODE) or S3– (RESET) to change the step filter
setting. Press and hold S4 (SET) for 2 seconds to exit Deep
Set Mode.
20
REPLACING THE BATTERY AND MASTER RESET
When the display starts to dim or goes blank, it is time to
replace the battery.
If the display is not uniformly dim or blank, and appears to
display "erroneous data" , do a Master Reset by pressing all
3 buttons simultaneously for 3 seconds and then release.
The display should go blank, then turn all segments on, then
display 0 steps in Step Mode.
Note: All the settings will return to their default setting values.
If you need to change the battery, the settings will also revert
to default settings.
22
VIEWING YOUR RESULTS
Once you put on your pedometer with the cover closed, it
will automatically begin to record your steps and activity
time. Repeatedly press the MODE button to cycle through the
pedometer modes:
STEPS g T IME g STEPS
Activity time is counted automatically whenever steps are
being counted.
• TIME is time spent in step activity.
Or, loop a badge
holder, then
Note: For extra accuracy, the default Step Filter Setting is 1.
put into pocket
See page 21 to learn more.
(Badge holder
not included)
RESETTING YOUR PEDOMETER
Most people prefer to reset counts daily. To reset your
counts: From STEP or TIME mode, press and hold the yellow
RESET button for at least 2 seconds. You'll see the values all
go back to zero.
OTHER SETTINGS
The Step Filter setting is accessed through a special "deep
set" mode.
To enter this mode, press and hold the S1 (SET) button for
4 seconds. T he screen will display a flashing single digit.
Note: T he unit will save any changes and exit set mode after
30 seconds unattended.
Can be set
from 0-5
steps
To replace the battery:
1. Insert a coin into the slot on the
bottom of the case, and twist to
loosen the faceplate. Remove
faceplate and set aside.
2. Locate the battery holder as seen
on sketch. Pull out the old battery,
and push a new LR-44 battery into the holder,
with positive terminal (+) facing up.
3. Snap faceplate back into place, hooking the bottom
two tabs first, then closing by pressing together at the
top two tabs.
-
D
W
XL
IGI
ALKER
.COM
STEP TIME
SET
MY
GOAL
0
20
40
60
80
100%
XL
120
G
JW200
S3-
S1,S2,S4
S3+
Set Step Filter set point
17
19
21
Battery
23