Digiop Black BLK-IPE4101 Руководство по быстрой установке - Страница 2

Просмотреть онлайн или скачать pdf Руководство по быстрой установке для Медиаконвертер Digiop Black BLK-IPE4101. Digiop Black BLK-IPE4101 3 страницы. 4-channel h.264 network video encoder

Печатать страницу

In the IP Setup window, click the Static option bullet. If you have other compatible network settings

you want to apply to the device, enter them in the appropriate locations. Click Setup to continue.

In the Login window, enter the ID and PW

(password) for your encoder, then click Login. The

default administrator values for the ID and PW are

root and pass.

In the IPAdmin Tool window, click Refresh. Verify that the entry representing the encoder now

shows the (new) static IP address.

Repeat these steps to setup the other three encoder IP channels.

Continue with procedure Step 5. Setup encoder Basic Configuration.

Installing encoders on LANs without DHCP

Configuring the network settings of your encoders includes these steps:

Determine the network settings of your computer.

—

Check the network for compatibility with the default static network settings of your encoder.

—

Find four network settings (IP addresses) that are not in use and can be assigned to the IP

—

channels of your encoder.

Attach the encoder to the network, power it on, and configure each IP channel with new

—

network settings.

Determine the network settings of your computer

At a PC attached to the LAN where your encoder will be connected, determine the IP address, subnet

mask, and default gateway of your PC. To find this information:

Hold down the Windows key and press r to

open the Run dialog box.

Type cmd in the entry field, then click OK to

open the Command Prompt window.

At the command prompt, enter ipconfig. The response will show the your PC's network

settings.

Record the IP Address, Subnet Mask, and Default Gateway for your PC's Ethernet adapter for

reference later.

NOTE If you are using Windows Vista or Windows 7, the IP address is identified as the "IPv4 Address."

Check the LAN for default IP address compatibility

Before connecting your encoder to the LAN, check the network to see if IP address 192.168.0.100 is already

in use. At a Microsoft Windows computer attached to the LAN where the encoder will be connected, open

a Command Prompt window and enter: ping 192.168.0.100

The "Request timed out" response indicates that the IP address is not in use and the encoder can be

connected without causing conflicts. If the response from the ping command received a "Reply..", the IP

address is in use. Contact Technical Support for further assistance, if needed.

www.digiop.com

Find network settings (IP addresses) that are not in use

At your PC, find an IP address on your network that is not in use:

Write down the EXACT IP address of your PC up to the third/last period. Using the example

shown above, this expression is: 192.168.5. After the third period, include any number

between 1 and 254 that is different from the one in your PC's IP address, 3. As a first try, let's

choose 75, which will form the IP address 192.168.5.75.

Next, use the ping command in the Command Prompt window to see if this IP address is in

use on your network. Enter: ping 192.168.5.75.

In the example shown above, the message "Reply from 192.168.5.75: .." indicates that

your PC can reach a device with that IP address, and that address is in use (i.e., you cannot

use it for your encoder).

Since the ping test showed that 192.168.5.75 is in use, try another number between 1 and

254. Let's try to ping 192.168.5.20. At the command prompt, enter: ping 192.168.5.20

In this test, the message "Request timed out" indicates that your PC cannot reach the

device with that IP address, and that address is probably not in use. If this test showed that

this IP address is in use, try other IP addresses using the steps above until an unused address

is found.

Repeat these steps to find IP addresses for the other IP channels of your encoder.

Attach your encoder to the network, power it on, and configuring it with new network settings

Connect the encoder to the LAN, then plug in the power adapter to power it on. Wait until the

initialization process completes (about 4 minutes) before continuing.

Open the directory IPAdminTool directory on your computer, then double click the file

IPAdminTool.exe to start the application. When the IPAdmin Tool starts, it will discover all the IP

devices it supports that exist on the network. The discovery process may take a few minutes.

In the Product list, find the entries with the MAC addresses of the encoder you installed. If all four IP

addresses are not shown, click Refresh once a minute until all four addresses are shown.

Right click the encoder entry with Rack Info R0,B0,M0 (IP channel associated with Vin1), then

select IP Address.

In the IP Setup window:

Select the Static option if it is not selected.

Enter the new IP address for your encoder into the IP Address field.

Enter the subnet mask of your computer into the Subnet Mask field.

Static Option