Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion Руководство по конфигурации - Страница 4

Просмотреть онлайн или скачать pdf Руководство по конфигурации для Переключатель Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion. Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 8 страниц. Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Также для Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion: Примечание по установке (14 страниц), Руководство по решению (17 страниц), Примечание по установке (46 страниц), Белая книга (19 страниц), Описание (1 страниц), Бюллетень продукции (6 страниц), Уведомление (4 страниц), Информационный лист (9 страниц), Информационный лист (18 страниц), Белая книга (18 страниц), Примечание по установке (28 страниц), Руководство по устранению неполадок (11 страниц), Примечание по установке (18 страниц), Руководство пользователя (17 страниц), Примечание по установке (24 страниц), Руководство (19 страниц), Примечание по установке (36 страниц)

Печатать страницу
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion Руководство по конфигурации
Configuring and Monitoring the Switch Fabric Functionality
Table 4-1
Modules
Between fabric-enabled modules (when no nonfabric-enabled modules are
installed)
Between fabric-enabled modules (when nonfabric-enabled modules are also
installed)
Between fabric-enabled and nonfabric-enabled modules
Between non-fabric-enabled modules
1. In show commands, displayed as dcef mode for fabric-enabled modules with DFC3 installed; displayed as fabric mode for
2. Displayed as fabric mode in show commands.
Configuring the Switch Fabric Functionality
To configure the switching mode, perform this task:
Command
Router(config)# [no] fabric switching-mode allow
{bus-mode | {truncated [{threshold [number]}]}
When configuring the switching mode, note the following information:
•
•
When you enter the no fabric switching-mode allow bus-mode command, power is removed from any
Caution
nonfabric-enabled modules installed in the switch.
•
•
•
•
Monitoring the Switch Fabric Functionality
The switch fabric functionality supports a number of show commands for monitoring purposes. A fully
automated startup sequence brings the module online and runs the connectivity diagnostics on the ports.
Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide, Release 12.2SXF
4-4
Switch Fabric Functionality Switching Modes
other fabric-enabled modules.
To allow use of nonfabric-enabled modules or to allow fabric-enabled modules to use bus mode,
enter the fabric switching-mode allow bus-mode command.
To prevent use of nonfabric-enabled modules or to prevent fabric-enabled modules from using bus
mode, enter the no fabric switching-mode allow bus-mode command.
To allow fabric-enabled modules to use truncated mode, enter the fabric switching-mode allow
truncated command.
To prevent fabric-enabled modules from using truncated mode, enter the no fabric switching-mode
allow truncated command.
To configure how many fabric-enabled modules must be installed before they use truncated mode
instead of bus mode, enter the fabric switching-mode allow truncated threshold number command.
To return to the default truncated-mode threshold, enter the no fabric switching-mode allow
truncated threshold command.
Chapter 4
Purpose
Configures the switching mode.
Configuring a Supervisor Engine 720
Switching Modes
1
Compact
2
Truncated
Bus
Bus
OL-3999-08