FIBARO FGS-222 Руководство по эксплуатации - Страница 2
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Переключатель FIBARO FGS-222. FIBARO FGS-222 4 страницы. Double relay switch
Печатать страницу
ENG
OPERATING MANUAL
DOUBLE RELAY SWITCH
FGS-222-EN-A-v1.01
Remotely Controlled Double Relay Switch of Fibaro System is
designed to operate in a wall switch box or in locations where the
control of an electric device (up to 1.5kW) is needed.
It is also possible to send a signal to any system that is to be
integrated with Fibaro system.
Specifications
Power supply:
110 - 240V ~
50 - 60Hz
Power consumption:
to 0,8W
Operational temperature:
0 - 35°C
Dimensions (L x W x H):
42,50 x 38,25 x 20,30 mm
For installation in boxes:
Ø ≥ 50mm
Rated load current:
6,5A per channel for resistive
load, but total current can not
exceed 10A*
Overcurrent protection:
required external 10A circuit
breaker
Active element:
micro-gap relay switch μ
Device control:
remotely - radio waves
directly - push buttons
Radio protocol:
Z-Wave
Radio signal power:
1mW
Radio Frequency:
868,4 MHz EU;
908,4 MHz US;
921,4 MHz ANZ;
869,2 MHz RU;
865,2 MHz IN;
Range:
up to 50 m outdoors
up to 30 m indoors
(depending on building materials)
Comply with EU directives:
RoHS 2011/65/EU
LVD 2006/95/EC
EMC 2004/108/EC
R&TTE 1999/5/EC
Technical Information
• Controlled by FIBARO system devices or any Z-Wave controller.
•
Electronic switch is a remote control unit.
• Microprocessor control.
• Active element: electromagnetic, micro-gap relay switch.
• The device may be operated by momentary and toggle
push-buttons.
•
To be installed in wall switch boxes of dimensions allowing for
installation, conforming to provisions of applicable regulations.
I General information about Fibaro system
FIBARO is a wireless system, based on Z-Wave technology.
FIBARO provides many advantages when compared to similar
systems. In general, radio systems create a direct connection
between the receiver and transmitter. But the radio signal is
weakened by various obstacles located on its path (apartment
walls, furniture, etc.) and in extreme cases it fails to transfer
required data. The advantage of FIBARO system is that its devices
apart from being transmitters and receivers of signals, they are also
a signal "duplicators". When a direct connection path between the
transmitter and the receiver can not be established, the connection
may be achieved through other intermediate devices.
FIBARO is a bi-directional wireless system. It means that the signal
is not only sent to the receivers but also the receivers send the
confirmation of its reception. This operation confirms their status so
to check whether they are active. Safety of the FIBARO system
transmission is comparable to the safety of transmission in data bus
wired systems.
FIBARO operates in the free band for data transmission. The
frequency depends on radio regulations in individual country . Each
FIBARO network has its own unique network identification number
(home ID), which is why it is possible to co-operate two or more
independent systems in a single building without any interference.
Although Z-Wave is quite new technology, it has already become
recognizable and officially binding standard, similarly to Wi-Fi.
Many manufacturers in various industries offer solutions based on
Z-Wave technology, guaranteeing their compatibility. This means
that the system is open and it may be extended in the future. Find
more information at www.fibaro.com.
FIBARO generates a dynamic network structure. After FIBARO
system is switched on, the location of its individual components is
automatically updated in real-time through status confirmation
signals received from devices operating in a "mesh" network.
The In-Wall Double Relay Switch is hereinafter referred to as Fibaro
Switch. It is designed to switch on/off devices connected to its
terminals using radio waves, controllers and a push button directly
connected to Fibaro Switch.
II Assembling Double Relay Switch
CAUTION
Read this manual before attempting to install
!
the device! Failure to observe recommendations
included in this manual may be dangerous or cause
a violation of the law. The manufacturer, Fibar
Group Sp. z o.o., will not be held responsible for any
loss or damage resulting from not following the
instructions of operating manual.
!
CAUTION
Product must be installed on a 10A line.
DANGER
Danger of electrocution! Electronic switch is
designed to operate in electrical home installation.
Faulty connection or use may result in fire or electric
shock.
DANGER
Danger of electrocution! All works on the device
may be performed only by a qualified and licensed
electrician. Observe national regulations.
DANGER
Danger of electrocution! Even when the device is
turned off, voltage may be present at its terminals.
Any
works
introducing
configuration of connections or the load must be
always performed with disconnected voltage
(disable the fuse).
CAUTION
Do not connect the device to loads exceeding
!
recommended
values.
accordance with the diagram presented in the
manual. Improper connections may be dangerous.
1. Before installation ensure that the voltage supply is
disconnected.
2. Connect Double Relay Switch as shown on the diagram.
3. Place the switch in the switch box.
4. Arrange the antenna (tips are presented further).
Single switch - mains electricity power connection
L
N
Double switch - mains electricity power connection
L
N
Fig.1 Wiring diagrams for Double Relay Switch.
NOTES FOR THE DIAGRAM:
N - terminal for neutral lead
L - terminal for live lead
IN - input terminal for load power supply
Q1 - output terminal of the first load
Q2 - output terminal of the second load
S2 - terminal for key no. 2
S1 - terminal for key no. 1 (has the option of entering the device in
learning mode)
B - service button (used to add or remove a device from the system)
Fig.2 Installation of Fibaro Relay Switch in wall switch box.
!
changes
into
the
!
Connect
only
in
i
S1 S2
L N
B
Q2 Q1 IN
SWITCH
S1 S2
L N
Q2 Q1 IN
B
SWITCH
CAUTION
The switch box must be compliant with the relevant
national safety standards and it's depth should not
be less than 60mm.
CAUTION
The device is designed for installation in wall
switch boxes and can work only with the electrical
connectors compliant with the relevant safety
standards.
NOTE
Durability of the device depends on applied load.
For resistive load (light bulbs, etc.) and 6,5A current
per channel, the durability exceeds 200 000
switches.