Sharp Carousel R-1405, Carousel R-1406 Руководство по эксплуатации - Страница 12

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Микроволновая печь Sharp Carousel R-1405, Carousel R-1406. Sharp Carousel R-1405, Carousel R-1406 48 страниц. Over the range microwave oven
Также для Sharp Carousel R-1405, Carousel R-1406: Руководство по установке (32 страниц), Технические характеристики (2 страниц)

Печатать страницу

R-1405

R-1406

DOOR OPEN MECHANISM

The door is opened by pushing the open button on the control

panel, refer to the Figure D-1.

When the open button is pushed, the open button pushes up

the open lever, and then the open lever pushes up the latch

head. The latch heads are moved upward and released from

latch hook. Now the door will open.

Door

Open lever

Figure D-1. Door Open Mechanism

DOOR SENSING AND PRIMARY INTERLOCK

SWITCHES

The primary interlock switch is mounted in the lower posi-

tion of the latch hook and the door sensing switch in the

secondary interlock system is mounted in the upper posi-

tion of the latch hook. They are activated by the latch heads

on the door. When the door is opened, the switches interrupt

the circuit to all components. A cook cycle cannot take

place until the door is firmly closed thereby activating both

interlock switches. The secondary interlock system con-

sists of the door sensing switch and secondary interlock

relay located on the control circuit board.

MONITOR SWITCH

The monitor switch is activated (the contacts opened) by the

latch head on the door while the door is closed. The switch is

intended to render the oven inoperative by means of blowing

the monitor fuse when the contacts of the secondary interlock

relay (RY2) and primary interlock switch fail to open when the

door is opened.

Functions:

1. When the door is opened, the monitor switch contact

close (to the ON condition) due to their being normally

closed. At this time the secondary interlock relay (RY2)

and primary interlock switch are in the OFF condition

(contacts open) due to their being normally open contact

switches. And the contacts of relay (RY1) are in the ON

condition (contacts close).

2. As the door goes to a closed position, the monitor switch

contacts are first opened and then the door sensing switch

and the primary interlock switch contacts close. (On

opening the door, each of these switches operate

inversely.)

DESCRIPTION AND FUNCTION OF COMPONENTS

Latch heads

Latch hook

Door sensing

switch

Monitor switch

Primary interlock switch

3. If the door is opened, and the secondary interlock relay

(RY2) and primary interlock switch contacts fail to open,

the monitor fuse blows simultaneously with closing of the

monitor switch contacts.

CAUTION: BEFORE REPLACING A BLOWN MONITOR

FUSE TEST THE DOOR SENSING SWITCH,

SECONDARY INTERLOCK RELAY (RY2),

RELAY (RY1), PRIMARY INTERLOCK SWITCH

AND MONITOR SWITCH FOR PROPER OP-

ERATION. (REFER TO CHAPTER "TEST PRO-

CEDURE").

NOTE: MONITOR FUSE AND SWITCH ARE REPLACED

AS AN ASSEMBLY

TEMPERATURE FUSE (MG)

The temperature fuse located on the fan duct assembly is

designed to prevent damage to the magnetron if an over

heated condition develops in the tube due to cooling fan

failure, obstructed air guide, dirty or blocked air intake, etc.

Under normal operation, the temperature fuse remains closed.

However, the temperature fuse will open at 302½F (150½C)

causing the oven to shut down.

NOTE: This is a fuse. It does not reset.

THERMAL CUT-OUT (HOOD )

This thermal cut-out located on the right base plate flange

(turntable motor side). It is designed to automatically turn on

the hood fan motor whenever the hot air rising from the

conventional range below causes the temperature at the

thermal cut-out to rise to 140½F (60½C) or higher, thus

removing this hot air from around microwave oven. When the

temperature around the thermal cut-out drops to 113½F

(45½C) or lower, the thermal cut-out shuts off the hood fan

motor.

THERMAL CUT-OUT (CAVITY )

This thermal cut-out is located on the bottom of the oven

cavity. It is designed to prevent damage to the oven unit if the

food in the oven catches fire due to overheating produced by

improper setting of cooking time or failure of control unit.

Under normal operation, the thermal cut-out remains closed.

However, the thermal cut-out will open at 293½F (145½C)

causing the oven to shut down. The defective thermal cut-out

must be replaced with a new one.

TURNTABLE MOTOR

The turntable motor rotates the turntable located on the

bottom of the oven cavity, so that the foods on the turntable

cook evenly during cooking. Turntable will turn in either

direction. The turntable motor can be turned off by touching

TURNTABLE ON/OFF pad.

COOLING FAN MOTOR

The cooling fan motor drives a blade which draws external

cool air. This cool air is directed through the air vanes

surrounding the magnetron and cools the magnetron. This air

is channelled through the oven cavity to remove steam and