Sharp Carousel R-1600 Руководство по эксплуатации - Страница 32
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Микроволновая печь Sharp Carousel R-1600. Sharp Carousel R-1600 48 страниц. Over the range microwave oven
Также для Sharp Carousel R-1600: Руководство по эксплуатации (28 страниц)
Печатать страницу
R-1600
R-1601
R-1602
2. Hold the center of the bracket which supports the shaft
of the fan motor on the flat table.
3. Apply the screw lock tight into the hole (for shaft) of the
fan blade.
4. Install the fan blade to the shaft of fan motor by pushing
the fan blade with a small, light weight, ball peen hammer
or rubber mallet.
5. Install the fan motor to the hood duct with the two (2) screws.
CAUTION:
* Do not hit the fan blade strongly when installing
because the bracket may be disfigured.
* Make sure that the fan blade rotates smooth after
installation.
* Make sure that the axis of the shaft is not slanted.
1. Disconnect the power supply cord.
2. Open the door and block it open.
3. Remove the three (3) screws holding the base cover to
the oven cavity
4. Remove the base cover from the oven cavity by pulling
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the hood fan motor and the hood duct from the
oven cavity, referring to the procedure of " HOOD FAN
MOTOR, HOOD DUCT AND OVEN LAMP SOCKET
REMOVAL".
STIRRER COVER AND STIRRER FAN INSTALLATION
1. Put the stirrer fan on the stirrer cover to match the stirrer
fan shaft to the center of the stirrer support.
2. Insert the shaft of stirrer fan to the shaft of stirrer motor.
3. Insert the cutout of stirrer cover to the tabs on the ceiling.
4. Install the stirrer cover to the oven cavity, and secure it
by one canoe clip.
1. Disconnect the power supply cord.
2. Remove one (1) screw holding the hood exhaust louver
to oven cavity front flange.
3. Remove the hood exhaust louver from the oven by
pushing the right and left tabs of the hood exhaust louver.
(Refer to procedure of "HOOD EXHAUST LOUVER
6. Install the hood duct to the oven cavity with the one (1)
7. Re-install the wire leads to the hole of the hood duct.
8. Connect the wire leads to the fan motor and chassis
9. Refer to procedure of "OUTER CASE REMOVAL". And
TURNTABLE MOTOR REMOVAL
5. Disconnect the wire leads from the turntable motor.
6. Remove one (1) screw holding turntable motor to the
7. Now the turntable motor is free.
STIRRER MOTOR REMOVAL
5. Disconnect the wire leads from the stirrer motor.
6. Remove the two (2) screws holding the stirrer motor to
7. Remove the stirrer motor from the waveguide.
8. Now, the stirrer motor is free.
9. When installing the stirrer motor, the shaft of stirrer
OVEN LAMP REMOVAL
4. Lift the oven lamp cover up.
5. Now, the oven lamp and the socket are found.
6. Screw the oven lamp off from the lamp socket.
7. Now, the oven lamp is free.
30
screw.
support, referring to the pictorial diagram.
reverse their procedure. And re-install the outer case.
Table
down and moving to the left slightly.
oven cavity.
the waveguide of the oven cavity.
motor must be inserted to the stirrer fan shaft. Refer to
the procedure of "STIRRER COVER AND STIRRER
FAN INSTALLATION".
Shaft
Stirrer Fan
REMOVAL")
Shaft
Center of
bracket
Stirrer Cover
Canoe Clip